Outside Dimensions of the Outer and and Inner Tube on the Pro Series A-Frame Top Wind Trailer Jack

Question

Question:

What are the outside Tube, and inside Tube outside Diameter dimensions?? I am looking for outside Tube diameter of no more than 1 7/8, with inside Tube diameter of 1 5/8, in order to fit my trailer A-Frame Tong below the mounting bracket.

asked by: Gary S

0

Expert Reply:

The outer tube diameter where the mounting flange is welded on to the Pro Series Round, A-Frame Jack, item # PSEA20000103, is 2-1/4 inches. The inner tube that extends and retracts has an outer diameter of 2 inches, see photo.

At this time we do not have a Jack with an outer tube diameter of 1-7/8 inches and inner tube diameter of 1-5/8 inches. Your best options would most likely be to enlarge the hole in your mounting plate for a 2-1/4 inch diameter jack or to go with a frame mounted option like the Pro Series Snap-Ring Swivel Marine Jack, item # PSEJ10000101, if there is room on your trailer frame.

expert reply by: Robert G

0

click to enlarge

Answer 1

1.9 inch is going to be a bit too small. Would 2 inch work? That's the closest we have like the Dutton Lainson part #DL22530 that you referenced. Maybe you could enlarge the hole with a dremel type grinder.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

If your Ford F-450 has an actual bed and is not a cab and chassis model (with a service bed or flatbed) then you can use the Curt universal folding gooseneck ball rail kit #C61502. You could then use Curt hitch #C-52 or #C65500. A custom hitch for a…

view full answer...

Answer 12

Yes, our Dexter leaf spring part #DX74XR is the same as the part number 072-079-00. This is a 7-leaf spring for an 8,000 lb trailer axle that is 24-7/8 inches.

view full answer...