Will the Kodiak Hydraulic Brake Hose Fit a Titan Premier Disc Brake Kit

Question

Question:

Does the Kodiak BH-3MFS-1-5 hose match up to the Titan T2HRCM10DAC directly? If not what will I need to make them work together? The reason I am asking is because the Titan brake kit has steel line and I hope to use copper-nickel brake lines.

asked by: Ray F

1

Helpful Expert Reply:

Yes, the 3/8"-24 male fitting on the Kodiak Hydraulic Brake Hose part # BH-3MFS90FF-1-5 will match up to the 3/8"-24 female fitting on the Titan Premier Disc Brake Kit part # T2HRCM10DAC. A 1/8" diameter hose and 3/8"-24 fitting is more or less an industry standard for brakes and will be the same across brands.

expert reply by: Conner L

1

Answer 1

In order to find a replacement you will have to identify what you currently have on the trailer. Since you mentioned the rotor I'm assuming you have disc brakes. If you have an over-the-hub rotor you won't need to replace the entire hub, just…

view full answer...

Answer 2

Let's start with the similarities. Both kits are compatible with L44649 and L68149 bearings and a 10-19 grease seal. Both kits are intended for use with a 3500 lb axle. Both are intended for marine applications and use dacromet rotor/hub…

view full answer...

Answer 3

Yes, the direct replacement for your Titan 225S passenger's side brake caliper is the #K71-773-02. For the driver's side use part #K71-773-01. These brake calipers are compatible with 3,500 lb axles with 10 inch brakes, which according to…

view full answer...

Answer 4

The Titan Premier Disc Brake Kit #T2HRCM10DAC that you referenced has a hub bore of 1.980 inches, so you have identified the correct set of Bearing Buddy grease caps for use with it, part #BB1980A-SS.

view full answer...

Answer 5

To get the best braking power for your boat trailer you would want to have disc brakes on both axles. If you happen to be limited to one axle then you would want the rear outfitted. With a 5,000lb boat you likely have two 3,500lb torsion axles. The…

view full answer...

Answer 6

The DB-42 is an older style of UFP 3,500 lb axle disc brake components. The Kodiak kits like the part #K2HR35D will fit in replacement of that and would be an upgrade so this would be a great solution. It comes with everything you'd need to…

view full answer...

Answer 7

The Dacromet-Coated brake calipers included with the Titan #T2HRCM10DAC Premier Disc Brake Kit do indeed feature stainless pistons and guide bolts. The exterior of the caliper and the rotors are Dacromet coated for corrosion resistance.

view full answer...

Answer 8

To use the Titan Disc Brake Kit and Aero 7500 Actuator w/ Manual Lockout, part #T2HRCM10DAC on your Four Winns trailer you will need to check a few parts on your trailer. You will need to make sure the 14 inch wheels your Four Winns trailer have a 5…

view full answer...

Answer 9

The Dexter Brake Actuator part #099-175-20 replaced the Titan 60 that has a master cylinder with a fitting at the end. The fitting is a 3/16 inverted flare where the brake lines connect to. You do not need an extra fitting when you use the actuator.…

view full answer...

Answer 10

I can help you pick out the correct hub, but we don't have a cross-reference part number for the one you listed. In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first…

view full answer...

Answer 11

I will start by saying that your TDE 11033L hub uses the #L68149 inner bearing and #L44649 outer bearing, which means you have a pretty standard #84 spindle on a 3,500 pound axle. With that said, we do not carry Tie Down Engendering products, so the…

view full answer...

Answer 12

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...