Recommendation For Replacement Hubs For Dexter E-Z Lube Torsion Axle

Question

Question:

Picture of axle label sent. Please recommend hubs.

asked by: Jason

1

Helpful Expert Reply:

Thank you for the information but I need more details to help you because Dexter has several torsion axle options. To determine the right trailer hubs, you will need to know your axle capacity. The easiest way to find this out is to look for a plate/sticker somewhere on the axle that provides information like part numbers, lengths, axle capacity.

If you can not find a label then find the size of your axle tube: Round with 1-3/4 inch diameter=2,000-lb axles, Round with 2-3/8 inch diameter=3,500-4,400-lb axle, Round with 3 inch diameter=7,000-lb axle.

Next, determine the bolt pattern so we can narrow down hub options.

Finally, find the size of bearings by either finding the stamped part number on the bearing or by measuring them with a digital caliper like Item # PTW80157. Measure the spindle at the inner and outer bearing seats.

After you have found out this information, send it to me and I can make specific recommendations.
I have attached links with additional information and videos for you to check out that will help.

expert reply by: Brint H

1

click to enlarge

Jason K.

1/23/2018

Picture of axle label sent. Please recommend hubs.

Reply

Brint H.

1/24/2018

Based on the picture you sent, it looks like you have a 2,500-lb trailer axle. We still have several options regarding hubs and drums and which one you need will be determined by your bearings and bolt pattern of your wheels. Common bearings for a 2,500-lb to 3,500-lb axle are inner bearings like Item # L68149 and outer bearings like Item # L44649. A common bolt pattern is 5 on 4-1/2 inch. I have attached some articles that go more into details about bearings and bolt patterns in case you need them. Based on this bearing and bolt pattern information, I recommend: 1. Trailer Idler Hub Assembly, Item # AKIHUB-545-35-EZ-K. This assembly fits E-Z Lube axles, works with standard axles from most manufacturers including Dexter, and has a 5 on 4-1/2 inch bolt pattern. It also comes with bearings, races, grease seal, grease cap, and lug nuts. 2. Trailer Hub and Drum Assembly, Item # AKHD-545-35-EZ-K. This assembly fits E-Z Lube axles, works with standard axles from most manufacturers including Dexter, has a 5 on 4-1/2 inch bolt pattern, and is compatible with electric and hydraulic drum brakes. It comes with bearings, races, grease seal, grease cap, and lug nuts. If these do not work for you, send me your bearing sizes and bolt pattern and I will make a correct recommendation. I have also attached additional information and videos for you to check out that can help with your project.

Reply

Answer 1

I have a few things for you to check when it comes to not being able to pair your iPhone with the Curt Echo #C51180. The first thing to do is make sure that you're pairing your phone with the Echo through the app. If you paired it through…

view full answer...

Answer 2

First check to make sure that your iPhone is up to date on its iOS updates. Then check to make sure you have the most up to date version of the Curt Echo App in your app store. You will want to make sure that your Bluetooth connection is on and the…

view full answer...

Answer 3

When the LED light on the Curt Echo part #C51180 does not illuminate that means the brake controller is not getting power from the 12V pin or the ground is bad. On a 7-way trailer connector, the 12V power function does not need to be connected for…

view full answer...

Answer 4

In your pictures I can see the Dexter part number 8-201 on the hub so the correct replacement hub would be the part #8-201-51UC3.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...