How to Install the Camco RV Drain Valve

Question

Question:

Can I just plug in this drain valve or does it need to screw in?

asked by: Gordon

0

Expert Reply:

The Camco RV Drain Valve # CAM22243 is threaded so it will not plug in, you will need to screw it in. The valve has 1/2 inch and 3/8 inch diameter male NPT threads and is for use with vinyl tubing. I've added a link to a video review for you to take a look at.

expert reply by: Kyle S

0

Answer 1

There isn't a difference in handling between bias and radial trailer tires; bias tires are designed more for hauling heavier loads and won't flex as much on the side walls. The downside is they'll run a bit hotter than radial…

view full answer...

Answer 2

When installing the Camco RV Drain Valve w Flange #CAM22223 you would not need to use sealant as long as you use the proper size tubing. Either 1/2 inch or 3/8 inch tubing.

view full answer...

Answer 3

Since you have already determined that it is a ground issue (which is almost always the problem) I would try sanding down the area you are installing the clearance light on. A good ground will have a solid connection to a clean, bare metal surface.…

view full answer...

Answer 4

There is a drain valve for you that will work; the Camco RV Drain Valve for 1/2" or 3/8" Diameter Drain Hose - Male NPT Thread #CAM22243 has, as the title suggests, a 3/8" diameter male NPT thread so it will work for you.

view full answer...

Answer 5

The Camco RV Drain Valve #CAM22243 is a 2-piece item. If you refer to the linked photo you will see it is composed of a threaded base part that will fit both 1/2-inch and 3/8-inch RV drain hoses and a handle part that inserts into the hollow cylinder…

view full answer...

Answer 6

The ground pin of a trailer side 7-way connector like the 7-Way Molded Trailer Wire Connector, 4' Long #H20043 you were looking at is the 5 o'clock position as shown in the included picture. For the vehicle side of the 7-way connector it…

view full answer...

Answer 7

If you were wanting to just plug in your current 7-Way on your popup to a 7-Way that is connected to your auxiliary battery then you could install the Hopkins #HM47210 on your trailer. Then you would need to ground the white wire to a clean,…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...