Clevis Adapter for B&W Adjustable 2-1/2-Inch Ball Mounts BWTS20040B and BWTS20040C

Question

Question:

is there a clevis I can add to my ball mount? I have part BWTS20040B.

asked by: Rich

0

Expert Reply:

Yes, you can use Clevis Adapter # BWTS35200B with your B&W Adjustable 2-1/2-Inch ball mount # BWTS20040B. The clevis has a 1-1/8-inch hole diameter.

This adapter also work with the chrome-finish version of your ball mount, part # BWTS20040C.

expert reply by: Adam R

0

Answer 1

To determine the amount of rise/drop you'll need, take a measurement from the inside top edge of the hitch receiver tube to the ground. Then, measure from the bottom of the trailer coupler to the ground. The difference between the two…

view full answer...

Answer 2

I do have an option for you but there isn't a pintle hook adapter for the B&W Tow & Stow Ball Mount. There is however a version of this ball mount which comes with a pintle hook but you can't add just that part to an…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Robert, The Curt Pintle Hook #C45908 would require that your EZ Loader boat trailer has a lunette ring for the coupler. From what I can see the 26-30ET should have a surge brake coupler that would couple to a standard ball mount. You'll need…

view full answer...

Answer 9

Hi James, To my knowledge the Reese Goosebox is the only replacement option that won't void the frame warranty. That being said, the frame warranty is typically only a year so you really aren't losing much voiding it, especially if you've…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could find…

view full answer...