Measurements on the Curt Trailer Hitch Class II Receiver

Question

Question:

I have some questions about the Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4 Item # C12064 I need to know the measurement between the frame rails and the height of the frame rails. I want to see if I can custom adapt it to a specific vehicle.

asked by: Rod

0

Expert Reply:

I contacted the manufacturer that assembles the Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4 Item # C12064 and they informed about the true measurements.

The hitch measures 9.56” from the frame rail to the bottom of the receiver tube. There are 6 mounting holes on the hitch, 3 on each side. Center to center on the two mounting holes closest to the rear of the vehicle is 42.25”. Center to center on the pair of mounting holes towards the front of the vehicle is 40.94”.

Although these there the measurements, we at etrailer don't recommend using a hitch for a vehicle that it isn't deigned for.

Please let me know if you need any clarification or additional measurements.

I am willing to see if we carry a universal hitch that fits what you need. I just need the measurements that you are looking for and year, make, and model of your vehicle. We have universal hitches that fit a range of frame widths.

expert reply by: Timothy G

0

Answer 1

We do have a hitch that fits your 2015 Dodge Challenger Hellcat like with the Curt part #C12064 which we have had customers come back and tell us it fit their Hellcat well.

view full answer...

Answer 2

Yes, Curt trailer hitch #C13093 and #C12064 will fit your 2015 Dodge Charger. Note the 2015 Dodge Charger, the drivers side exhaust must be temporarily lowered and drivers side muffler removed and then reattached in order to install Curt trailer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hi Robert; hopefully your Roadmaster tow bar is one that attaches to direct-connect base plates as opposed to crossbar base plates; for example the 8,000 lb Roadmaster Sterling would be optimal. Assuming that, here is what you need to flat tow your…

view full answer...

Answer 10

You are on the right track. The only way we have that will allow you to use the Thule T2 Pro Xtr Bike Platform Rack part #TH69TX with the 2.5" receiver tube opening on your truck would be with adapter. For this, I recommend the Brophy Hitch…

view full answer...

Answer 11

I recommend the Roadmaster Dual Hitch Receiver Adapter, 10" Drop/Rise item #RM-077-10. This adapter was designed for this type of set up. Your Jeep Rubicon and Swagman E bike rack weigh well below the 10,000 lbs maximum capacity of this hitch. I…

view full answer...

Answer 12

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...