What is the Second Hitch Pin Hole Used for on the Draw-Tite Max-Frame Trailer Hitch Receiver # 75600

Question

Question:

Reference product: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2 Item # 75600 There is an extra threaded hole on the receiver, from what I can tell to firm up/stabilize the ball mount. Is there a special screw that goes in there? Something that could be hand tightened? If there isnt something specific, what is the thread spec?

asked by: Tony R

0

Expert Reply:

The second pin hole that you are seeing on the Draw-Tite Max-Frame Trailer Hitch Receiver # 75600, for your 2013 BMW X5, is indeed for the use of a stabilization device.

That second hole was for the Tow Ready J-Pin Stabilization Pin and Barrel Lockset # 63201, however, this part has been discontinued.
.

expert reply by: Jon G

0

Answer 1

The Curt Pin and Clip #F-4 that you referenced is designed to work on 1-1/4 inch hitches. The reason your hitch has a 1/2 inch hole and a 5/8 inch hole is because it is setup for an obsolete anti-rattle device Draw Tite J-Pin. We no longer carry the…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 12

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

What is the Second Hitch Pin Hole Used for on the Draw-Tite Max-Frame Trailer Hitch Receiver # 75600

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching