Is There a Difference Between Ultra Fab Scissor Jacks and Lippert Scissor Stabilizer Jacks

Question

Question:

What is the difference s between a stabilizer scissor jack and a plain scissor jack? Thanks

asked by: John O

0

Expert Reply:

There really isn't a difference between the intent and purpose of the Ultra-Fab Ultra Scissor Jack # UF48-979006 and the Lippert Scissor Stabilizer Jacks # LC285326.

One just has the word Stabilizer in the title and the other does not. Both will perform the same way and stabilize the trailer, only really difference is that the part # LC285326 has a 10,000 lbs capacity and the # UF48-979006 has a 6,500 lb capacity.

expert reply by: Jameson C

0

Answer 1

Tthe etrailer.com Electric Jack w/ Footplate #EJ-3520-BBX that you referenced has a 30 amp barrel fuse like #EJ-FUSE which is located in a flared opening right where the black power wire comes out of the motor housing. It is very easy to access and…

view full answer...

Answer 2

We actually carry the replacement fuse part #EJ-FUSE for RAM or etrailer.com trailer jacks, like part #EJ-3520-BBX. With that being said, I have reached out to RAM about this in the past and they have said that there isn't anything special about…

view full answer...

Answer 3

Sounds like the screw or the motor of the Lippert Smart Jack #LC643589 is damaged or has an internal issue. The switch is obviously working and the motor works in the harder direction so something funny is wrong with it. If it's within a year old…

view full answer...

Answer 4

As the jacks are raised an lowered, the upper mounting plate are designed to remain level. As you can see from the photo I edited, the ends of the jack uprights have gears or teeth built into them so that the mounting plate remains level. The…

view full answer...

Answer 5

Trailer manufacturers do not typically keep record of smaller parts such as the scissor jacks that would have come with your 2016 Keystone Springdale Summerland Mini 17. With that being said, just about any properly rated scissor jack will work great…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

I went ahead and pulled this Replacement I-Beam Jack Bracket #LC349975 from our warehouse to measure. I have attached the dimensions below. Hope this Helps.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

For your electric jack, there are only three possible explanations for your jack not working with a charged battery. Either power is not getting to your motor, your motor is bad, or your ground connection isn't working properly. To test power,…

view full answer...

Answer 10

For frame mounted camper tie downs that are a confirmed fit for your 2016 Dodge Ram 3500 Dually we have the TorkLift camper tie downs part numbers #TLD2131 for the front and part #TLD3109 for the rear.

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Is There a Difference Between Ultra Fab Scissor Jacks and Lippert Scissor Stabilizer Jacks

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching