Wiring Diagram for Lippert Stabilization Jack LC298707

Question

Question:

What is the wiring diagram for the LC298707. There are no instructions or diagram to show the wiring schematic.

asked by: Ed M

0

Expert Reply:

I have included a picture showing how the motor and switch wire up on the Lippert stabilizer jack # LC298707.

expert reply by: Michael H

0

click to enlarge

Richard V.

8/8/2020

I have a 2014 jayco eagle 27.5 with the lippert electric jack, my wiring fell off at the vinyl coating at the connectors, will like to know if a wiring diagram is available please note a also have a remote that powers jacks all the wiring diagrams have only a switch and power. What I'm looking for a a diagram that shows the wiring that includes the wires for a remote. Thanks,

Reply

Jon G.

8/18/2020

Since it sounds like your stabilizer system is connected to a larger section of your Jayco you might need to reach out to Jayco directly to see if they have a specific wiring diagram for your application. The only stabilizers we have include the High-Speed # LC298707 which comes with the switch, and the Ground Control TT # LC672136 which does come with a controller, but all of the connections are plug and play.

Reply

Richard V.

8/18/2020

@JonG Thanks for you're response, the wires are not plug and play, they are joined by metal wire nuts, that's why they rusted apart, the reason I sent you this problem is the advise from Jayco because they don't have a drawing, now I'm in a pickle. The drawing above would be a simple fix but would not operate my remote

Reply

Jon G.

8/28/2020

@RichardV I'm sorry to hear that. I wish that wiring diagrams were universal with colors and everything but unfortunately they are not. I'd try checking some of the forums that are dedicated for Jayco owners to see if someone could send you a pic of their setup if what you're trying to connect is OEM.

Reply

Answer 1

I believe you are referring to the Lippert Components High-Speed Power Stabilizer Jack part #LC369774 that comes with the white switch part #LC144214. Lippert was not able to provide me a wiring diagram for the white switch but was able to give me…

view full answer...

Answer 2

For your Lippert Components Power Stabilizer Trailer Jack #LC298707 the wiring is pretty simple. There are two wires that come out of the motor and they are both used as power or ground depending on the direction you want to turn the motor. To…

view full answer...

Answer 3

I attached a picture that I got from Lippert that shows the wiring diagram for their stabilizer jacks like the part #LC298707.

view full answer...

Answer 4

On each individual electric brake magnet the amperage draw would be 3.0 to 3.2 max amps at 12 to 13 volts on 7-inch brake magnets and 3.2 to 4.0 max amps at 12 to 13 volts on 10 and 12-inch brake magnets. The max amperage draw for the brake magnets…

view full answer...

Answer 5

On the Lippert Power Stabilizer Jack #LC298707 for your Forest River Evo Trailer Trailer there should be a 20 amp (or higher) fuse/breaker located inline with the red power wire coming from the switch before it reaches the battery. Check to make…

view full answer...

Answer 6

There are a few things you can check to make sure the brakes are adjusted correctly, but it sounds like there may be a short in the system. I would start by checking the trailer wiring connector on the truck and trailer for corrosion. If there is…

view full answer...

Answer 7

I went out to our warehouse and test fit some SnapPads on the feet of the Lippert High-Speed Power Stabilizer Jack #LC298707 and found that the 6" square SnapPads were a fit. If your 2022 Forest River Vibe travel trailer only has one…

view full answer...

Answer 8

We have actually heard from Lippert about this type of issue and they recommend replacing the 6 amp fuse with a 30 amp fuse. This should resolve the issues you're describing.

view full answer...

Answer 9

I spoke to my contact at Lippert about wiring the toggle switches for the Lippert Electric Trailer Jack #LC285318. They stated that they don't have any schematics on this unfortunately but what we were able to do is snap a photo of the back…

view full answer...

Answer 10

Yes, I confirmed with Lippert that the Replacement Top Cover for Lippert Components Electric Trailer Jack part #LC285160 will fit your Lippert 3,500 Lb Electric tongue Jack 1817941.

view full answer...

Answer 11

In regards to the Lippert Components High-Speed Power Stabilizer Jack part #LC298707, the red wire on the motor will run through the 6 amp circuit breaker to the switch. I have attached a diagram of this for you as well although wire colors are not…

view full answer...

Answer 12

Because the power leg is protected by a 20 amp circuit breaker, it's recommended that 12 gauge wire be used. I've provided a wiring diagram of the #LC298707 for you. You can see an install video by clicking the provided link.

view full answer...

Wiring Diagram for Lippert Stabilization Jack LC298707

Product Page this Question was Asked From

Continue Researching