Replacement Bearings, Races, and Grease Seal for the EZ Loader Kit 300-015907

Question

Question:

I’m looking for a bearing kit for my Ez Loader trailer. The Ez Loader part Number is 300-015907. Thank you

asked by: David G

0

Expert Reply:

The bearings, races, and grease seal that are included in the EZ Loader bearing kit 300-015907 that you referenced are found as parts # L68149, # L68111, # L44649, # L44610, and # 168255TB.

expert reply by: Jon G

0

Answer 1

I looked up the manual online for the UFP A-60 Surge Brake Actuator and found the following bullet points for greasing. "Lightly grease rear rollers and hold them in the pockets in the sides of the master cylinder while inserting entire…

view full answer...

Answer 2

In terms of capability the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K #DX89FR is a good replacement option. The problem is the design of your old TDE LP7000 which was installed inside the…

view full answer...

Answer 3

Yes, you can weld on the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K item #DX56FR you referenced. You will want to make sure you remove the zinc coating and get down to the bare metal. I…

view full answer...

Answer 4

Thank you for the pictures of your coupler. You are going to need to replace your entire surge actuator coupler as the A-50 is obsolete and we do not have any parts to repair it. We have the Dexter DX7.5L A-60 Brake Actuator #DX73FR which you can…

view full answer...

Answer 5

Hi Charles, While we don't currently offer the inner member that you're needing for the UFP A-70 we do offer a compatible replacement with the Dexter DX7.5L A-60 Brake Actuator #DX33FR. This is the entire actuator assembly along with…

view full answer...

Answer 6

The proper replacement inner assembly member for your UFP 34043 would be indeed be the the Dexter #DX99FR which is compatible with disc brakes. The replacement has an electric lock out and has a 7500K capacity and is intended to work with a 2 inch…

view full answer...

Answer 7

The difference is the trailer tongue size the coupler was designed to fit. The part #DX29FR is designed to fit a 3 inch by 4 inch straight tongue whereas the part #DX56FR is designed to fit a 3 inch by 5 inch straight tongue. Aside from that they…

view full answer...

Answer 8

That's a really good question, and there is a difference between the 7,500 lb Dexter DX7.5L A-60 actuators for disc brakes; the differences are both in what they fit, as well as their length. - 14" Long & Top-Mounted For…

view full answer...

Answer 9

Hey Scott, the bolt holes of the Dexter DX7.5L A-60 Brake Actuator w/ Electric Lockout - Disc #DX56FR are 3" apart horizontally and 2-1/2" apart vertically. The holes are 5/8" from the top and bottom of the actuator.

view full answer...

Answer 10

The Dexter DX7.5L A-60 Brake Actuator w Electric Lockout part #DX29FR for disc brakes and part #DX27FR for drum brakes use 1/2" diameter mounting hardware. We have used both grade 5 and grade 8 bolts when doing installations of them but the…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K #DX56FR you were looking at is confirmed to work with tandem axle trailers like yours, and is a great option as long as your trailer uses disc…

view full answer...

Replacement Bearings, Races, and Grease Seal for the EZ Loader Kit 300-015907

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching