Thickness and Will Hinge Kit SH300 Rust

Question

Question:

what is gauge, will it rust?

asked by: Mike W

1

Helpful Expert Reply:

I wish we had a hinge kit that had hole drilled in it already but none of the ones we offer do and we do not have any screw kits designed specifically for them either.

expert reply by: Jameson C

1

Mike W.

10/13/2017

what is gauge, will it rust?

Reply

Jameson C.

10/13/2017

The steel used is 0.074 inches thick so that is just a little larger than 1/16 of an inch (its closest to 5/64 of an inch). It's stainless steel so it will not rust either.

Reply

Answer 1

All of our piano hinges like the 3" Wide #SH300 do not come pre-drilled. We do not carry any which are pre-drilled.

view full answer...

Answer 2

The stainless steel allow of the Hinge part #SH300 that you referenced is 304.

view full answer...

Answer 3

A piano hinge like the part #SH300 would work great for you to allow you to fold your aluminum ramp in half. This hinge is stainless steel too so it won't rust. You might put some thin rubber between the hinge and the ramp to prevent galvanic…

view full answer...

Answer 4

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 5

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Answer 6

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 7

From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a standard cap that fits this size so the Bearing Buddy is…

view full answer...

Answer 8

M12-1.5 and 1/2"-20 threads are not going to be interchangeable. The diameter of an M12 thread is only going to be 0.4724" while 1/2" threads are going to be 0.500" in diameter. We currently only have 1/2"-20 Lug Nuts…

view full answer...

Answer 9

On oil bath hubs the seals are different than standard grease seals. The correct replacement for what you have is #91030. Unitized oil seals like this have a part that stays fixed and a part that rotates with the hub for optimum leak protection. I…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

It sounds like the 2022 Chevy Silverado 3500 you are getting has the short bed. In that case, yes, you definitely want the sliding 5th wheel hitch for clearance. The good news is you will not need to purchase the entire B&W Companion #BWRVK3775.…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Thickness and Will Hinge Kit SH300 Rust

Product Page this Question was Asked From

Continue Researching