Could Curt Hitch # 13015 Fit 2000 Dodge 3500 Roadtrek Van 190

Question

Question:

Hi Ive been looking at your pictures and video on this hitch and it looks like it should fit my 2000 dodge 3500 roadtrek 190. Do you have any input on this? I would like to order it today.

asked by: STEVE W

0

Expert Reply:

I looked up pictures of 2000 RoadTrek RV's made from Dodge Vans and some of them appear very similar to the standard Dodge van they were built off of and our hitches like part # 13015 would fit and work well.

Check out the picture I attached and if the rear bumper is the same as what is in the picture this hitch would fit and work well.

The second picture I attached shows the underside of the van with the hitch installed. You would need to compare that to your vehicle as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

There are no front mount trailer hitches that will fit the 1999 Dodge Full-Size vans. They are not built on the same platform as the Ram trucks of the same generation so the front mount hitches for the Ram trucks will not fit the Ram Vans. You can…

view full answer...

Answer 2

We don't have any front mounted hitches or bike racks available for your 2000 Dodge Camper Van. The best option I could list for you would be to go with a rear mounted hitch and bike rack. For a hitch I would recommend the #13015 if you don't…

view full answer...

Answer 3

Several hitches, both Class III and Class IV types, are offered for the different versions of the 1999 full-size Dodge van. The key factor in selecting the right one is the type of bumper on the van, either a standard bumper or a step bumper. The…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 8

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...