Does Camco RV Water Heater Anode Rod 11563 Fit Suburban SW6D Water Heater

Question

Question:

Is CAM11563 the correct anode to use with a Suburban SW6D water heater? Are there any other choices, that might be better, like pros and cons??

asked by: Rich

0

Expert Reply:

Yes, the Suburban SW6D water heater is considered a Mor Flo water heater so the part # CAM11563 is the correct part.

expert reply by: Jameson C

0

Answer 1

If your plan was to install a brake controller you'd have to also run the black wire of the 7-Way Adapter part #30717 to the to the positive post of your vehicle battery as well as the ground you mentioned. The Curt Echo part #C51180 that you…

view full answer...

Answer 2

If you have a 4-pole wiring setup now and you want to install a wireless trailer brake controller you will use an adapter like Curt #C57672 or Hopkins #37185. Both install by plugging in to your 4-pole and by making additional wiring connections…

view full answer...

Answer 3

The Camco RV Water Heater Anode Rod part #CAM11563 is what you need for the suburban SW6D water heater.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Does Camco RV Water Heater Anode Rod 11563 Fit Suburban SW6D Water Heater

Product Page this Question was Asked From

Continue Researching