What Size Bolts are Used to Install Hitch in a 2015 Toyota Sienna

Question

Question:

Size the bolts that hold hitch in place. 2015 toyata sienna

asked by: James T

1

Helpful Expert Reply:

The Curt hitch part # C13105 which is a fit for your 2015 Toyota Sienna comes with bolts that are size M12-1.25x40.

I attached an install video for this hitch for you to check out as well.

expert reply by: Jameson C

1

click to enlarge

Answer 1

The bolts for the CURT Trailer Hitch, #13105, for the 2006 Toyota Sienna, are M12 - 1.25 x 40 hex bolts. I have included a link to the installation details below for the hitch. Re-tapping a weldnut can be difficult and you could end up breaking it…

view full answer...

Answer 2

According to the instructions, the bolts for hitch part #75237, are M12 x 1.25 x 40MM bolts. If you do not have a metric tap and die set, I would just take one of the bolts to a hardware store and match the tap to the bolt.

view full answer...

Answer 3

The Curt trailer hitch part #C13105 comes with all of the install hardware needed, but the bolts are size M12-1.25x40 hex. If you need the replacement hardware you would want part #RHK. If you enter the part number on this product page we will ship…

view full answer...

Answer 4

The Curt Trailer Hitch Receiver #C13105 that you referenced, which is confirmed to fit your 2018 Toyota Sienna, uses six M12-1.25 x 40 hex bolts and six 1/2 inch conical toothed washers for installation. We can indeed provide you with this hardware…

view full answer...

Answer 5

Of the 2 inch Curt hitches we offer for your 2017 Toyota Sienna the part #C13343 is the one to go with as it has only the hitch opening visible down below the bumper. The instructions do recommend removing the rear fascia to install the hitch. We…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

What Size Bolts are Used to Install Hitch in a 2015 Toyota Sienna

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching