Bolt Size to Install Draw-Tite Class III Trailer Hitch 75237 on 2005 Toyota Sienna
Question:
Do you have the exact specs for the bolts used to connect the hitch? I have tried spraying the nuts welded into the frame with WD40 and cleaning with a wire brush but still cant get all the bolts in 3 are in, 2 are started but I cant get in any farther and 1 I cant even start. I want the specs so I can try using a tap to clean out the threads of the nuts in the frame. Thanks.
asked by: Brad
Expert Reply:
According to the instructions, the bolts for hitch part # 75237, are M12 x 1.25 x 40MM bolts. If you do not have a metric tap and die set, I would just take one of the bolts to a hardware store and match the tap to the bolt.
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 675 lbs TW
- 4500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 675 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: Trailer Hitch Installation - 2004 Lincoln Town Car - Curt
- Shop: Draw-Tite Max-E-Loader Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Suspension Enhancement
- Shop: Air Lift 1000 Air Helper Springs for Coil Springs - Rear
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: What Size Hex Bolts are Used to Install a Curt Trailer Hitch on a 2015 Chevy Equinox
- Q&A: Size of Factory Bolts For Installation of Curt Trailer Hitch Receiver in Factory Weldnuts
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Q&A: Cleaning Out Weld Nuts to Install a Trailer Hitch on a 2006 Toyota Sienna
- Q&A: What Bolt Size is Used to Install Curt Trailer hitch 13200 on a 2014 Toyota highlander
- Video: Trailer Hitch Installation - 2008 Toyota Sienna - Draw-Tite 75237
- Article: Trailer Hitch Installation Tips
- Video: etrailer.com Trailer Hitch Installation - 2011 Toyota Sienna e98853
- Video: Trailer Wiring Harness Installation - 2012 Toyota Sienna 118498
- Q&A: Exhaust Pipe of 2006 Toyota Sienna is Rattling Against Hitch
- Q&A: Bolt Size for Curt Trailer Hitch, # 13256 and Availability of Replacement Hardware
- Search Results: wiring harness
- Video: etrailer.com Trailer Hitch Installation - 2011 Toyota Sienna
- Video: Trailer Hitch Installation - 2005 Toyota Camry - Curt
- Video: Trailer Hitch Installation - 2018 Toyota Sienna - Draw-Tite
- Q&A: Which Class III Trailer Hitch Receiver Provides Most Ground Clearance for 2007 Toyota Sienna LE
- Search Results: hitch wiring
- Search Results: trailer hitch wiring
- Shop: BOLT brand vehicle and hitch locks
Gene
6/17/2020
Is it possible to just purchase the replacement bolts/washers for this hitch? If yes, how much is it and where can I purchase it? Thanks!