Adjustable RV Hitch Installation To Frame Piece Holding 4 Inch Bumper

Question

Question:

Adjustable RV hitch I have a 2003 Dutchman classic it has I-beam but it has a 4 inch bar coming from hiding for the bumper should I install this to the 4 inch they are about 16 inches long welded to the I-beam to support the bumper

asked by: Ted S

0

Expert Reply:

The Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703 can be mounted to that 4 inch bar your mentioned. That is considered a part of the frame and is a safe location for this trailer hitch receiver.

expert reply by: Jason S

0

click to enlarge

Answer 1

I attached a picture I received from Draw Tite that shows the dimensions of Draw Tite hitch part #82201 that you are looking for.

view full answer...

Answer 2

The Multi-Fit Motor Home Trailer Hitch, #82201, has an overall height of 5-5/8". Please note the attached image.

view full answer...

Answer 3

On your 2020 Ford F-150 the Curt Front Mount Trailer Hitch #C31083 will sit further up than the Draw-Tite alternative and actually won't affect the truck's ground clearance at all. The 2" receiver on the hitch will protrude…

view full answer...

Answer 4

The bolt holes on the Multi-Fit Motor Home Trailer Hitch part #82201 are spaced 8-1/2" apart front to back. The bolt holes spaced left to right can be adjusted as needed up to 68". I have attached a photo with these measurements for…

view full answer...

Answer 5

We definitely have options for adding a hitch to the back of your 2013 Rushmore 5th wheel. We do have a few different attachment styles as well, so I have two options below. First, and the way I recommend going, will be the Draw-Tite Multi-Fit…

view full answer...

Answer 6

Yes, for your 2020 Ford F-150 the Curt Front Mount Trailer Hitch Receiver #C31083 will work perfectly. This hitch is designed specifically for your truck and it will use existing holes in it's frame rails for a simple bolt-on, no-drill…

view full answer...

Answer 7

The Draw-Tite Multi-Fit Motor Home Trailer Hitch, 47" - 71" wide #82201 has a maximum tongue weight of 300 lbs. If you have a frame that is shorter then the Draw-Tite #5350 is a great option with a 500 lb tongue weight. If you are unsure of…

view full answer...

Answer 8

For your 2018 Ford F-150 I recommend the Curt Front Hitch #C31083 because it's make in the USA, is easy to install, and has plenty of capacity at 9,000 lb line pull. In case you were looking for a plow too I attached a link to this page that has…

view full answer...

Answer 9

Using a hitch extender is safe as long as you stay within the limits specified of 50 percent of the hitch and vehicle load capacity, and 350 lb tongue weight capacity of part #HE06. The other option to provide additional clearance from your spare…

view full answer...

Answer 10

The center to center measurement of the mounting bracket bolt-holes for the Stromberg Carlson Adjustable Accessory Hitch Receiver #SC45MR is 5-7/8". Additionally, there are two other bolts holes on the angle brackets that measure 3-1/8"…

view full answer...

Answer 11

The Curt Adjustable Width Trailer Hitch Receiver for RVs part #13703 does have 4-7/8" tall brackets like you mention. Since I cannot recommend to cut down the brackets, I recommend to use an adjustable hitch that attaches to the bottom of the…

view full answer...

Answer 12

Yes, the Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide, #13703 is for bike racks, cargo carriers, etc. and can be bolted to the vehicle frame or welded on for a no-drill application.

view full answer...