Bolt Through Swing Away Trailer Jack For Limited Space Trailer Tongue

Question

Question:

I need a bolt-on like fxp15 but have limited room on tongue due to some tabs the support poles fit in for this tent camper. I have 12 in. to fit on .if the wheels will come of when in up position.

asked by: JD M

1

Helpful Expert Reply:

The Fulton Bolt-Thru Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,500 lbs # FXP15W. This jack is 12-3/4 inches retracted and has a clearance of 12-1/2 inches from mounting bracket to top of jack. This will be the closest jack to fitting your needs.

If you don't need the bolt thru style, I recommend the Round Swivel Marine Jack w/ Wheel - Bolt On - Zinc - Sidewind - 11" Travel - 1,200 lbs # MJ-1200B which is bolt on and has the 12-1/2 inch retracted length.

Unfortunately there is not an easy caster wheel removal unless you take out the wheel's axle bolt.

expert reply by: Jason S

1

Answer 1

We can help you with a new jack for your 1992 StarCraft pop-up camper. Usually an A-frame trailer like this will use a jack that mounts in the standard receptacle behind the coupler. Jacks for this kind of A-frame installation are linked for you.…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Unless you want to completely clean out every bit of grease you will need to stick to a LMX red grease like item #L11390 that comes with the CE Smith Trailer Idler Hub Assembly item #CE13515. You can use your blue marine grease but you can't mix…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

To determine which hubs would be best for your boat trailer there are a few things you will need to look at; the axle capacity on your boat trailer, the inner bearing number, outer bearing number, grease seal number, the bolt pattern of your wheels,…

view full answer...

Answer 9

I think you are on the right track. The Fulton Bolt-Thru Swivel Marine Jack you mentioned, part #F1411300301, is rated at 1500 lb. With the jack fully retracted, the distance from the bottom of the mounting bracket to the floor is 12.5". I think…

view full answer...

Answer 10

Swapping the mounting hardware on a jack can be done, but it will depend on the specific mounting hardware of the jacks. Shelby jacks and parts are becoming more difficult to locate, so I would recommend replacing your Shelby hardware with something…

view full answer...

Answer 11

The Magnum name isn't used anymore, but the jack hasn't changed much. You'll be needing part #FXP15L for a 12 inch lift or #FXP15W for a 10 inch lift.. If you click the provided link, you can see a product description video fearing the…

view full answer...

Answer 12

What you have there is a Dutton Lainson jack. There is no longer a direct replacement jack, but you can use the #DL22580 which will be an upgrade. This is a swivel jack with a 1,500 lb capacity and 12" of lift. This has dual wheels for easy…

view full answer...

Bolt Through Swing Away Trailer Jack For Limited Space Trailer Tongue

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching