Shank Option for 2-1/2 inch Hitch Used with Strait Line Weight Distribution

Question

Question:

I need a lower shank to adjust for my new truck. Looking for options. My current shank is a 54970 with what appears to be the 58167 head for my weight distribution trunnion with dual cams. I need 2 addtl inches lower from my current lowest setting. My current head assembly only shows a casting number 113802 Rev. C. Assume this is 58167? Please confirm if 54977 shank will work with my head assemby? My receiver is now also 2 1/2, but will use a reducer sleeve if necessary. Open to any other options... Thanks,

asked by: Tom J

0

Expert Reply:

We can help you find a shank that offers a drop that is 2 inches lower than the part # RP54970 that you have. The part # RP54977 though cannot be used with weight distribution heads that use serrated washers to change the angle of the bars like the part # RP58167 that you have.

The part # EQ90-02-4900 is a fit for 2-1/2 inch hitches like you have and will offer around 5 inches more of a drop than what you have.

Or for more drop we have the part # C17123 but it fits a 2 inch hitch so you'd need a sleeve adapter like part # C45405 which will naturally add a little more play to your system which isn't ideal.

expert reply by: Jameson C

0

Answer 1

It looks like your 2019 Lance 2465 travel trailer tops out at 6,830 lbs. The Strait-Line Weight Distribution w/ Sway Control item #RP66074 will work for you trailer. It has a tongue weight range of 600 lbs - 1,200 lbs which is perfect for your…

view full answer...

Answer 2

The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow, this figure also includes the weight of any cargo behind the rear axle of the tow vehicle. I…

view full answer...

Answer 3

Hi Joe, Yep, you heard correct, you can go from a 2 inch shank to a 2-1/2 inch shank with your Reese weight distribution hitch without issue. One of the following 2-1/2 inch shanks should have the right rise/drop for your application. Here are the…

view full answer...

Answer 4

Yes, the Reese Dual Cam II Weight Distribution System #RP65FR is a great option for your 2023 Grand Design Imagine XLS 22RBE. To attach it to your 2019 Ford F-250 you will need a Shank #RP69FR and Reducer Sleeve #C45408 to go from the 3"…

view full answer...

Answer 5

You are not missing anything and you are correct. The Reese Weight Distribution Shank #RP69FR will provide 8.75" of drop. I have included a picture that shows the drop dimensions between each hole.

view full answer...

Answer 6

When we had the chance to install the Torklift hitch part #TLD1111-30 on a short bed truck like your 2023 Ram 3500 we did not have to modify the spare mount so I would not anticipate that being an issue. If you check out the install video link you…

view full answer...

Answer 7

To be able to tow a dump trailer at your 2016 Ford F-350's maximum towing capacity of 14,000 pounds, you will need to use a weight distribution system. In Ford's towing guide, they state that the maximum loaded trailer weight requires use of…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Shank Option for 2-1/2 inch Hitch Used with Strait Line Weight Distribution

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching