Curt Sliding 5th Wheel Hitch Compatibility With 2017 Ford F-350

Question

Question:

Is there a puck system to fasten this model to the new 2017 F-350 beds?

asked by: Mike

0

Expert Reply:

Curt E16 5th Wheel Trailer Hitch w/ R16 Roller - Slide Bar Jaw - 16,000 lbs # 16516 will fasten to the 2017 Ford F-350 Factory Puck System using the Reese Elite Series Underbed Rail Adapter for Standard 5th Wheel Trailer Hitches - 20,000 lbs # RP30156.

Curt makes the sliding hitch for this application and it is the Curt E16 5th Wheel Trailer Hitch w/ Slider for Ford Towing Prep Package - Slide Bar Jaw - 16,000 lbs # C16515-16020. You can get just the sliding base # C16020 if you already have the hitch head.

expert reply by: Jason S

0

Answer 1

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 2

The Ford OEM puck system is different than the Chevrolet/GMC OEM puck system therefore, you can't use a 5th wheel hitch from one in the other. The Ford OEM system has pucks which are much closer together than on the Chevrolet/GMC OEM system. The…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 7

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 8

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 9

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 10

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 11

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 12

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...