Trailer Hitch Recommendation for 1970 Ford F-100 with Standard Bumper

Question

Question:

I have a 1970 f100 with the standard chrome rear bumper..not the step bumper ..And I would like the receiver to be located right under said bumper ..Can you tell me what hitch to buy...

asked by: Mitch

0

Expert Reply:

For your 1970 Ford F-100 with a standard chrome bumper the Draw Tite hitch part # 41001 is a confirmed fit that will work well for you. The hitch opening will be right underneath the bumper as well.

expert reply by: Jameson C

0

Answer 1

Based on the frame dimensions you listed for your 1977 Ford F-250 you actually have a cab and chassis model which has the narrower 34 inch wide frame. That means instead the hitch you need is the Curt part #13028 which is confirmed as a fit for your…

view full answer...

Answer 2

The Curt Trailer Hitch Receiver part #13028 is designed to fit the following vechiles: - 88-91 CHEVY/GMC 4 DR CREW CAB ONLY - 73-79 FORD 250 CREW CAB - 73-06 CHEVY/GMC FULL SIZE CAB & CHASSIS w 34" FRAME - 73-06 FORD PICKUP: CAB AND CHASSIS…

view full answer...

Answer 3

The Hole spacing for the B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25198 are as follows(all measurements are for center of hole to center of hole). 34" Width Frame -Front holes- 28-7/8" -Middle and rear holes- 29-1/2"…

view full answer...

Answer 4

The B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25122 that will fit your 1986 Chevy K20 will measure 5.438" from the top of the frame brackets to the top of the receiver. If this is looking like it will not be enough to clear the bottom of…

view full answer...

Answer 5

I spoke with B&W about the B&W Heavy-Duty Trailer Hitch Receiver part #BWHDRH25198 and they informed me that the distance between the mounting holes left to right is 37-1/8".

view full answer...

Answer 6

The overall diameter of the 5.70-8 trailer tire is 18.1 inches. We have a few options for this size, and I recommend the Adco Ultra Tyre Gard RV Wheel Covers - 18" to 22" - Black #290-3975 because of their fit and the bungee ball fastening…

view full answer...

Answer 7

The overall diameter of the 5.70-8 trailer tire is 18.1 inches. We have a few options for this size, and I recommend the Adco Ultra Tyre Gard RV Wheel Covers - 18" to 22" - Black #290-3975 because of their fit and the bungee ball fastening…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...