Will Lippert LCI Powered Trailer Jack Require Grease Maintenance

Question

Question:

Do i grease any areas of the jack? I have had mine for two years and it works great.

asked by: Kris L

0

Expert Reply:

I spoke to my contact at Lippert and they confirmed that the Electric Tongue Jack # LC285318 does not require any grease maintenance. Therefore they didn't include a grease zerk, which is why you are unable to locate one.

expert reply by: Jameson C

0

Answer 1

Good news, I can help. I was able to find the service manual for the Lippert Ground Control 3.0 #LC358590 and found in that where Lippert recommends if the jacks are down for extended periods, it is recommended to spray exposed leveling jack tubes…

view full answer...

Answer 2

The Lippert Components Power Tongue Jack #LC285318 uses a standard 3-bolt a-frame type mounting scheme. It is designed to be installed in a specific orientation with the point of the triangular mounting plate facing the tow vehicle as with most of…

view full answer...

Answer 3

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 6

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 7

Lippert does not offer a replacement inner jack tube for their jack 1817941. When a jack is damaged in this way (which is more common than you want to know) it really is best to replace the entire jack for safety reasons. The outer tube on your jack…

view full answer...

Answer 8

Your typical electric jack is designed to fit an A-frame so the only one we carry that is a side mount is the Fulton XLT #F141401. However, you may be interested in the Trailer Valet JXS Drill Powered Swivel Trailer Jack #TV64FR. This jack has a hand…

view full answer...

Answer 9

Hey Frankie, The bracket for the Timbren Suspension Enhancement System #TFR250SDJ has a locknut in it that makes it feel like the bolt (part #4) is fully tightened when it's not. Their techs have stated that you just have to push past this point…

view full answer...

Answer 10

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 11

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...