Do All LED Trailer Lights Work with 12 Volt Power

Question

Question:

Hi, some of your lights say 12V on them, while others dont give the voltage. Arent they all 12volt or since Im looking for 12 volt, should I focus only on the listed 12 Volt lights? Im looking at the: UCL50CB MCL-50CRK MCL55RCB Thanks

asked by: Robert

0

Expert Reply:

Some vehicles run 24 volts (bigger vehicles like big rig type vehicles) and some older vehicles have 6 volt systems. But 12 volt is by far the most common.

The lights you are looking at, # UCL50CB, # MCL-50CRK, and # MCL55RCB will all work on a 12 volt system.

expert reply by: Michael H

0

Answer 1

Normally a tandem axle trailer only has one brake wire going to the vehicle, and it is typically blue. If you have two separate brake wires for your axles, that is fine and will not cause an issue. Having one wire ran along the trailer instead of the…

view full answer...

Answer 2

If the left turn signal illuminates when the right turn signal is activated then you have a short in the wiring harness or trailer connector which is causing the left turn signal wire (usually yellow) and the right turn signal wire (usually green) to…

view full answer...

Answer 3

First thing you should do at this point is test the 4-way of the wiring harness with a circuit tester part #PTW2993 for voltage on all of the right pins when the taillight signals are being applied. Just like in the video I attached. If the voltage…

view full answer...

Answer 4

We do not offer wishbone wiring that has a ground wire going down both sides. You really don't need it because the ground wire is for the plug itself not the lights and you want the ground close to the plug. I recommend using the 4-Way Wishbone…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...