Can Ultra-Fab Stabilizer Jack be Used at Rear of Trailer

Question

Question:

This ad recommends this product for the front of an RV, but is there a specific reason why this cannot be added to the back of my 32 foot bumper pull? I damaged the fragile scissor jacks that were back there.

asked by: JOHN

0

Expert Reply:

Yes, the Ultra-Fab Power Twin II Stabilizer # UF39-941704 can be used at the rear of your trailer. It's designed to fit trailer's with frames from 48 to 80 inches wide and has a lift of 30 inches.

expert reply by: Charles S

0

Answer 1

If you're talking about a space to sit between the mounting brackets of the Ultra-Fab Power Twin II Manual Stabilizer #UF39-941704 and the frame of the trailer then no, this stabilizer does not have spacers. If you're trying to gain more…

view full answer...

Answer 2

The mounting bracket for the Ultra-Fab Power Twin II Manual Stabilizer #UF39-941704 is approximately 35-3/8" in length. The frame height would dictate the amount of lift you would want but there are other factors to take into account. The…

view full answer...

Answer 3

The Ultra-Fab Power Twin II Electric Stabilizer for Trailers and RVs - 22" Lift - 6,000 lbs #UF39-941707 is a great product, but will only give you 3 inches of lift as you mentioned. That would be enough if you were always camping on level or…

view full answer...

Answer 4

I contact Ultra-fab and since the socket on the Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs part #UF39-941704 is not a standard hex socket head there is not a way to raise and lower the stabilizer with a power drill. The socket on…

view full answer...

Answer 5

The Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs #UF39-941704 measures 5" from the trailer frame to the lowest hanging part of the jack. I confirmed this with my contact at Ultra-Fab. Since your trailer has a lower profile it…

view full answer...

Answer 6

The frame width on your 2003 Keystone Cougar 5th wheel trailer will need to be between 48 and 80 inches (measured from the outside of the frame on one side to the outside of the frame on the other side) in order for the Ultra-Fab Power Twin II Manual…

view full answer...

Answer 7

The Ultra-Fab Power Twin II Manual Stabilizer #UF39-941704 that you referenced fits trailers that have frames that are 48 to 80 inches wide. Since you measured 67-1/8 inches wide this would easily fit your trailer.

view full answer...

Answer 8

The Ultra-Fab Power Twin II Manual Stabilizer, #UF39-941704, and similar products would have to be mounted just back from the A-frame part of the frame. They are meant to provide support and not lift the trailer so you would not need this type of…

view full answer...

Answer 9

The Lippert Components High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit - 30" Lift #LC298707 or #LC369774 only come with the motor. You can get a replacement motor and replacement arms but the main support beam and legs are not…

view full answer...

Answer 10

For your Grand Design Reflection 312BHTS I recommend the Ultra-Fab Slide-Out Supports #UF19-960002. Since your Reflection has the 2 opposing slides that carry the weight of most the kitchen and the seating areas the trailer is virtually teetering on…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Can Ultra-Fab Stabilizer Jack be Used at Rear of Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching