Overall Measurements of Foot and Where to Weld on Bulldog 2K Snap-Ring Swivel Jack
Question:
What is the size of the foot for this jack and the plate that is welded on? The frame that it will be welded on to is 4.25inch high. If the plate is 5inch and frame 4.25inch will that still be ok to weld?
asked by: Ray B
Expert Reply:
I went out to the warehouse to measure Bulldog trailer jack # BD151101. The overall length and width of the footplate is 7-1/2 x 4 inches.
The part that gets welded to the trailer is L-Shaped. The lip that rests on top of the frame it 4-9/16 inches long and 13/16 inches deep. I would weld the lip to the top of the frame the whole length. On the sides you can weld two 1 inch long 3/16 fillet welds per side of the plate.
Product Page this Question was Asked From
Bulldog Round, Snap-Ring Swivel Jack - Sidewind - 10" Lift - 2,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Sidewind Jack
- Swivel Jack
- 10 Inch Lift
- Weld-On
- With Rectangle Foot
- Bulldog
more information >
Continue Researching
- Search Results: trailer jack
- Search Results: bulldog trailer jack
- Shop: Replacement Weld-On L-Bend Bracket for Bulldog and Fulton Snap-Ring Swivel Jacks
- Shop: Bulldog Round, Snap-Ring Swivel Jack - Sidewind - 15-1/4" Lift - 2,000 lbs
- Shop: Pro Series Round, Snap-Ring Swivel Jack - Bolt On - Topwind - 10" Lift - 2,000 lbs
- Shop: Bulldog Round, Snap-Ring Swivel Jack - Sidewind - 10" Lift - 2,000 lbs
- Shop: Replacement Mounting Bracket for etrailer and Ram Snap Ring Swivel Jacks - Weld On
- Q&A: Outer Diameter of the Mounting Bracket Tube of the Pro Series Swivel Jack
- Q&A: Will the Pro Series Round Snap-Ring Swivel Jack Bolt on a 2 Inch by 2-1/2 Inch Trailer Tongue
- Q&A: Pro Series Ring Swivel Jack Trailer Accommodation
- Q&A: Swivel Jack for 6 Inch Tall and 4 Inch Wide Trailer Frame
- Q&A: Replacement Gear Kit for Bulldog Round, Snap-Ring Swivel Jack
- Q&A: Does Bulldog Jack 151101 Have Weight Capacity for 7,800 lb Trailer
- Q&A: How to Remove the Snap-Ring on the Bulldog Round Snap-Ring Swivel Jack # BD151101
- Shop: Trailer Hitch
- Shop: Dust Cap for Kodiak Disc Brake Kit
- Search Results: 44649
- Video: Choosing the Right Trailer Wiring
- Article: Trailer Wiring Diagrams
- Search Results: 25580
- Shop: Trailer Wiring
- Shop: Optronics LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 10 Diodes - Red Lens
- Article: How to Choose the Right Trailer Hitch Class
- Video: etrailer Class III Trailer Hitch Installation - 2016 Jeep Cherokee
- Shop: Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 68149
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Search Results: led turn signal
- Shop: Fifth Wheel Hitch