Overall Dimensions of the Pro Series Round, Snap-Ring Swivel Jack # PS1400300303

Question

Question:

Can you please supply me the overall dimensions of PS1400300303 jack? Im looking for a low profile top swivel jack.

asked by: Bill

0

Expert Reply:

I went out to the warehouse and measured the Pro Series Round, Snap-Ring Swivel Jack, item # PS1400300303, for you. The Overall height of the jack fully retracted is 17 inches.

The distance, fully retracted, from the center of the mounting plate to the top of the jack at the center of the crank mechanism is 6 inches. The handle sticks up another 2-3/4 inches when in the cranking position.

From the center of the mounting plate to the bottom of the jack the measurement is 11 inches when fully retracted.

The base plate, or foot, measures 4 inches by 7-1/2 inches.

This jack has a bolt hole pattern of 4-1/2 inches by 5-3/8 inches and the mounting plate can be turned to 180 degrees to use these measurements either way.

expert reply by: Robert G

0

Answer 1

There are jacks that will work for your 6" tall x 4" wide trailer frame, but they are going to need to be welded onto your trailer frame, something a professional welder should be able to do this in no time at all. The option I recommend is…

view full answer...

Answer 2

The differences between the two jacks is minimal. The main feature difference is that the Bulldog #BD178203 has the ASABE (American Society of Agricultural and Biological Engineers) compliancy certification whereas the ProSeries #PS1401440303 does…

view full answer...

Answer 3

Yes, the Pro Series Round Snap-Ring Jack, #PS1400300303, will bolt around your 2 inch by 2-1/2 inch trailer tongue. This jack can bolt to frames up to 3 inches wide by 4 inches tall and will have no problem fitting on your trailer. I have attached a…

view full answer...

Answer 4

The Pro Series Swivel Jack #PS1400300303 that you referenced should fit fine in your application. In the picture of the jack that I have provided has the measurements indicated. From the center of the mounting bracket to the foot plate is 11 inches.…

view full answer...

Answer 5

I went out to the warehouse to measure Bulldog trailer jack #BD151101. The overall length and width of the footplate is 7-1/2 x 4 inches. The part that gets welded to the trailer is L-Shaped. The lip that rests on top of the frame it 4-9/16 inches…

view full answer...

Answer 6

I have not heard of any complaints from customers about the Pro Series Trailer Jacks. The #PS1400800383 jack features a zinc plated inner tube and the jack is constructed of steel. The Pro Series #PS1400800383 is comparable to the Bulldog Square Jack…

view full answer...

Answer 7

I can recommend a replacement jack as Atwood was split up and acquired by companies like Lippert and Dometic, and there is not a replacement handle available for your Jack. The Bulldog Round, Snap-Ring Swivel Jack #BD151101 has a similar design with…

view full answer...

Answer 8

To remove the snap ring from the Bulldog Round, Snap-Ring Swivel Jack, #BD151101, you will need snap-ring or retaining ring pliers. These pliers are available at most local hardware and auto parts stores. The snap ring pliers will have two pins on…

view full answer...

Answer 9

Trailer jacks over time do sometimes fail and the issue is not that they were overloaded. Most of the time it's corrosion that gets into the nut and screw which eventually locks up the assembly.The Bulldog jack #BD151101 that you referenced has a…

view full answer...

Answer 10

To verify fitment of the Bulldog Round, Snap-Ring Swivel Jack #BD151110 on your trailer you will need to measure the diameter of the Bracket #F500242 on your trailer. The diameter of the outer part of the bracket needs to be 2-1/2" for the…

view full answer...

Answer 11

All of our jacks have a 3 on 3 bolt hole pattern and what I recommend is switching to a bolt-on snap-ring swivel jack like the Pro Series Snap-Ring #PS1400300303 because it fits up to a 3 x 4 inch tongue and has an 10-inch lift and 2,000 pound lift…

view full answer...

Answer 12

The Bulldog Round Snap-Ring Swivel Jack #BD151464 referenced in your question is indeed a weld-on trailer jack. It is designed to mount onto the Weld-On Bracket #F500242 with the Snap Ring #BD500241. For a similar trailer jack that uses a bolt-on…

view full answer...

Overall Dimensions of the Pro Series Round, Snap-Ring Swivel Jack # PS1400300303

Product Page this Question was Asked From

Continue Researching