Is Class l Ball Mount Available With 6-Inch Rise

Question

Question:

Looking for ball mount for class I hitch 1-1/4receiver that exceeds 6inch - do u sell such an item?

asked by: Everett

0

Expert Reply:

The biggest rise we offer in a 1-1/4 inch ball mount is 5-3/8 inches, and that is part # C45028.

This ball mount is a Class l and also features a 5-9/16 inch drop. This ball mount is rated for a gross towing capacity of 2,000-lbs. The hitch pin and clip I recommend is part # F-4.

For a 1-7/8 inch hitch ball I recommend part # C40001 and for a 2-inch ball I recommend part # C40018.

expert reply by: Jeffrey L

0

Answer 1

The maximum towing capacity of your 2017 Honda Accord is 1,000 lbs. The towing capacity of the hitch will not change the vehicle's towing capacity as the lower of the two ratings (vehicle/hitch) will always be the limiting factor. For your…

view full answer...

Answer 2

The Curt Drawbar for 1-1/4" Hitches part #C45028 (5-3/8" Rise) is the most amount of rise we offer for a standard ball mount that fits a 1-1/4" trailer hitch receiver. The 2" Hitch Ball can then be added with part #C40018. The…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...