Lippert Ground Control 3.0 - Rear Jack Leg Replacement Recommendations

Question

Question:

The rear jack shaft between the motor and the jack broke. Can you replace the shaft? If so, what is the cost for the parts. Have you had similar questions about shafts breaking?

asked by: John H

0

Expert Reply:

I spoke to my contacts at Lippert and the shafts of the jack legs are not available separately. You would have to replace the jack legs. They also have not heard of the shafts breaking either.

If you need a replacement left rear leg you would need # LC305339. For a right rear leg you would need the part # LC344792.

expert reply by: Jameson C

0

Answer 1

It sounds like you have the Lippert Ground Control Auto Leveling Landing Gear 3.0 part #LC358590 and are looking for replacement rear landing gear legs. For that you would want the part #LC344792 for the rear right leg and the #LC305339 for the rear…

view full answer...

Answer 2

I attached a dimension picture I got from Lippert for the Replacement I-Beam Jack Bracket #LC349975 that you referenced.

view full answer...

Answer 3

The Replacement Left Rear Leg for Lippert Components Ground Control 3.0 Electric Leveling System - Qty 1 #LC305339 has the following dimensions: 9 inch diameter foot plate 23-1/2 inches tall without foot plate 8-1/2 inches wide at widest point…

view full answer...

Answer 4

If you have reset the system and they are still not retracting, you will need to check a few things. First will be the fuses. If one or more of these have failed, it can cause the system to not function properly. Next will be ground connections. A…

view full answer...

Answer 5

It could be a loose wiring connection or corrosion, or you could have a damaged wire. You can check out the attached wiring drawing to see what you can check to try and find the problem. To correct the system errors I have attached the chart that…

view full answer...

Answer 6

I am sorry to hear about the issue you are having with your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part #LC358590. The first thing you are going to want to do is check for blown fuses on the control board. If the fuses are…

view full answer...

Answer 7

I assume you have the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part #LC358590? If that is the case then there is a manual override on both the top of the motor and bottom of the leg for each jack. Since the jack is retracted…

view full answer...

Answer 8

I spoke with my contact at Lippert and they told me that the problem is most likely gears on the tops of the legs broken or stripped, motor/gear box stripped, worm gear in legs stripped or cross shaft bolt broke. In any case though they recommend…

view full answer...

Answer 9

I attached a link to the install instructions for the Lippert Ground Control 3.0 part #LC675817 which is the kit the leg part #LC305339 is a part of. On page 6 of the instructions is the torque spec for mounting the jacks. Spoiler alert...it's 75…

view full answer...

Answer 10

The Trailer in Motion error message that you are receiving is due to the sensor detecting that the vehicle is moving. To use the auto level feature the trailer must be unhooked from the truck and not moving. If the sensor detects movement from either…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...