Replacement Brake Assemblies For Al-KO Or Hayes 4-Bolt Flange
Question:
Hi, I have a mid 80s? Travel trailer converted to a flat bed. 32ft 5th wheel with 6x5.5 bolt type wheel hubs. Outer bearing is a lm67048. Its the 4 hole backing plates. My problem is that my backing plate bolt holes measure, 3 1/4 top, 2 5/8 bottom, and 3 1/2 side. All measured center to center hole. Im having a hard time finding any backing plates that measure the same.
asked by: Garrett
Expert Reply:
The closest brake assemblies we offer to the dimensions you said you have are part # 23-105-09 for the left hand, and # 23-106-09 for the right.
The 4-hole bolt pattern is 3-1/4 inches for the top two holes, 2-1/2 inches for the lower two holes and the distance top to bottom is 3-3/8 inches. I know the measurements are off by 1/8 inch versus your measurements but I am sure these are what you are looking for. These are designed for either AL-KO/Hayes 4-bolt or standard 5-bolt flange and that have a capacity of 6,000-lbs per pair.
Products Referenced in This Question
Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange - 12" - Left Hand - 6,000 lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- LH
- 6000 lbs
- Brake Assembly
- Manual Adjust
- 12 x 2 Inch Drum
- Dexter
more information >
Product Page this Question was Asked From
Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange - 12" - Right Hand - 6,000 lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- RH
- 6000 lbs
- Brake Assembly
- Manual Adjust
- 12 x 2 Inch Drum
- Dexter
more information >
Continue Researching
- Shop: Dexter Electric Trailer Brakes - 12" - Left/Right Hand - 6K AL-KO/Hayes Axles
- Q&A: Replacement Trailer Brake Assemblies that Have 4 Bolt Pattern and 12 inch Diameter
- Shop: Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange - 12" - Right Hand - 6,000 lbs
- Shop: Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange - 12" - Left Hand - 6,000 lbs
- Shop: Mounting Bolts and Hardware for 12-1/4" Brake Assemblies - 8,000 lbs to 9,000 lbs
- Shop: Dexter Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 6,000 lbs
- Shop: Mounting Bolts and Hardware for 10" Single Brake Assembly
- Shop: Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb Axles - 12" - 6 on 5-1/2 - Pre-Greased
- Video: Dexter Electric Brake Assembly Review
- Q&A: Center Hole Diameter of Brake Assembly 23-106-09
- Search Results: al ko 12" brakes
- Q&A: Which Brake Drum is Used with Dexter # 23-105 and # 23-106 Brake Assemblies
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Integrated Drum - AKHD-655-6-K
- Article: Measuring a Trailer Tire
- Q&A: Which Hub and Drums and Braking Assemblies Fit Tandem 6000lb Phillips/Dexter Axles?
- Video: Redline Trailer Brakes BRKH10AS Review
- Video: Review of Dexter Trailer Leaf Spring Suspension - Suspension Kits - K71-359-00
- Q&A: AL-KO 6k Brake Assembly Recommendation with Offset 4 Bolt Mounting Pattern
- Q&A: 4-Hole Spacing Measurements on Dexter 12 x 2 Inch Electric Trailer Brake Assemblies
- Q&A: Brake Assembly Recommendation for 6,000 lb AL KO Trailer Axles
- Search Results: 23~105~09
- Search Results: 23~106~09
- Search Results: 185100
- Search Results: trailer hubs
- Search Results: trailer idler hub
- Search Results: breakaway kit
- Shop: Brake Controller
- Article: Adding Electric Over Hydraulic Disc Brakes
- Video: Review of Dexter Brake Flange Stud 7/8 Inch - 007-112-00
- Video: Review of Dexter Axle Trailer Brakes - Electric Brake Assembly - 23-105-09