Center Hole Diameter of Brake Assembly 23-106-09

Question

Question:

What is the measurement for the diameter of center hole ? 23-106-09 brake assembly.

asked by: Robert A

1

Helpful Expert Reply:

The center hole of the brake assemblies # 23-105-09 and # 23-106-09 measures 3-3/16 inches across. The kit for both of these is the part # 23-105-106-09 that you referenced.

expert reply by: Jameson C

1

Answer 1

Your dimensions are a little unique but I would assume you have an AL KO brand axle with a 6k axle and the correct assemblies would be the part #23-105-09 and #23-106-09. This is 12 inch in diameter assembly that can attach with a 4 or 5 lug bolt…

view full answer...

Answer 2

The mounting holes (4 hole pattern) on Dexter brake assembly, #23-106-09, are 3.09 inches on center for the top two holes and 2.55 inches apart on center for the bottom 2 holes. Top to bottom they are 3.40 inches apart on center. The holes can…

view full answer...

Answer 3

We have a set of brake assemblies fit to replace your 12 inch x 2 inch AL-KO electric brakes. The Dexter #23-105-09 left-hand side, #23-106-09 right-hand side. These brake assemblies are rated for 6,000 pounds per pair like your axle and have the…

view full answer...

Answer 4

Sorry about the problems you were having with our brake install/setup video. We have been having some issues with our servers here lately so that is probably why. For a 6k, 12 inch brake assembly with a 5 lug install bolt pattern you would want the…

view full answer...

Answer 5

The Dexter Electric Brake Assembly #23-106-09 is similar to the #23-106 except it is designed to fit both 4 bolt AL KO style bolt patterns as well as the standard 5 bolt patterns seen on most other brands. Since you have Al KO axles you'd most…

view full answer...

Answer 6

The closest brake assemblies we offer to the dimensions you said you have are part #23-105-09 for the left hand, and #23-106-09 for the right. The 4-hole bolt pattern is 3-1/4 inches for the top two holes, 2-1/2 inches for the lower two holes and the…

view full answer...

Answer 7

It sounds like you have the red wire attached to the illumination circuit of the truck and not to the cold side of the brake switch for a dedicated brake signal. This is why the indicator comes on when you turn on the head lights. If you are using a…

view full answer...

Answer 8

We do have a wiring diagram for you! Whether you have the 1,000 psi Dexter DX Series #K71-650 or the 1,600 psi Dexter DX Series #K71-651 the wiring will be the exact same. I have attached a wiring diagram and review videos for you to check out. Just…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...