Torque Specs for Hardware of Firestone Kit parT # F2525

Question

Question:

In the videos, I hear the torque to specifications but the installation PDF only mentions torque one time and that is not to exceed 20 ft lbs and that is only in one of the steps. Whats the actual torque spec for this product on the various bolts?

asked by: Alan

0

Expert Reply:

I attached a picture to this that shows all of the torque specs for the various mounting hardware components of this kit.

expert reply by: Jameson C

0

click to enlarge

Answer 1

When installing the Firestone Ride Rite #F2445 with the B&W #BWGNRK1257-5W you won't actually be leaving any bolt holes empty. I've attached an exploded diagram from Firestone that shows the air supply bolt actually has a nut/washer that…

view full answer...

Answer 2

Good question. Let's clear it up. On the Firestone Ride-Rite Air Helper Springs part #F2558 they are as follows. 1. The 5/8inch Nylon jam used to connect the upper bracket to the air spring? 15-20 ft/lb. 2. The 3/8inch hex bolt used to connect…

view full answer...

Answer 3

Thanks for the purchase and the kind words, and I can help you out here in regards to the torque of the Firestone Ride-Rite Air Helper Springs #F2445 that fit your 2013 Toyota Tundra. You always want to follow what is in the written manual as opposed…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Torque Specs for Hardware of Firestone Kit parT # F2525

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching