Verified Timbren Suspension Enhancement Fit for a 2004 Toyota Tundra

Question

Question:

could you check the part # on the timbrens i purchased . You have # ttortun4 other sites have tortun4 1t for my 2004 tundra access cab sr5 4x4. This is the midsize 2004-2006 model.Thanks

asked by: Brad

0

Expert Reply:

I checked with Timbren just now and for your 2004 Toyota Tundra they recommend the # TTORTUN4 so that would be the correct part number. We put an extra T in front of the part number but it's the same thing.

expert reply by: Jameson C

0

Answer 1

I really like the Timbren setups like the part #TTORTUN4 that you referenced. This will replace your bump stops and provide you with 6,000 lbs more of suspension support. That means your truck isn't going to bottom out when you are loaded. I like…

view full answer...

Answer 2

I spoke with my contact at Toyota and he said that Timbren helper springs #TTORTUN4 will fit your 2006 Toyota Tundra 4x4 TRD. I have included a link to a video review and a link to the installation details for you.

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

I have a similar slip-on towing mirror that is a fit for your 2004 Toyota Tundra, but it's not the part #11501 which is designed for Ford trucks. Instead you would want the Longview mirror part #CTM4000 which is a confirmed fit.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a standard cap that fits this size so the Bearing Buddy is…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Yes, the Curt hitch part #C77ZV is a fit for the 2023 Toyota Crown Hybrid. I attached a link to the install instructions as well as a link to an installer finder in case you wanted to find someone near you to install the hitch.

view full answer...

Answer 11

For your AL-KO 7210 braking assembly, you can use the Hydraulic Brake Kit #AKFBBRK-7 as a replacement. These braking assemblies measure 12" x 2", bolts onto a 5 bolt mounting flange, will work with wheel sizes from 14-1/2" to…

view full answer...

Answer 12

If your 2022 Chevrolet Tahoe does not have the factory tow package then the plug may not be there. If this is the case you would need to hardwire in a brake controller. If your Tahoe does have the tow package then the plug will be under the dash. The…

view full answer...