Timbren Helper Springs for a 2006 Toyota Tundra 4x4 TRD

Question

Question:

Will the #TTORTUN4 fit the 06 tundra 4wheel drive TRD Package

asked by: Tom A

0

Expert Reply:

I spoke with my contact at Toyota and he said that Timbren helper springs # TTORTUN4 will fit your 2006 Toyota Tundra 4x4 TRD. I have included a link to a video review and a link to the installation details for you.

expert reply by: Michael H

0

Answer 1

I checked with Timbren just now and for your 2004 Toyota Tundra they recommend the #TTORTUN4 so that would be the correct part number. We put an extra T in front of the part number but it's the same thing.

view full answer...

Answer 2

I really like the Timbren setups like the part #TTORTUN4 that you referenced. This will replace your bump stops and provide you with 6,000 lbs more of suspension support. That means your truck isn't going to bottom out when you are loaded. I like…

view full answer...

Answer 3

I went out and pulled both the Timbren kit part #TTORTUN4 and #TTORTUN4L from our warehouse to measure them for you and found that they both sit exactly 3-3/4 inches tall.

view full answer...

Answer 4

I have contacted Timbren and for the specific rear suspension kit that you referenced that #TOTTUN4, you will need approximately 6-1/4 inches of clearance between the frame and the leaf spring on your modified 2003 Toyota Tundra vehicle suspension. I…

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Timbren Helper Springs for a 2006 Toyota Tundra 4x4 TRD

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching