Can Over/Under Conversion Kit be Used to Lower a Trailer

Question

Question:

the axles on my rv have been flipped springs on the top of axle and it sits to high, does your kit allow me to put the springs on the bottom of the axles?

asked by: Christopher D

0

Expert Reply:

Yes. The over/under conversion kits such as # K71-385-00 for 3 inch axles or # K71-384-00 for 2-3/8 inch axles can be used to move the axle to the top of the leaf spring stack the same as moving the axle below. It will change the ride height by a little more than the diameter of the axle.

expert reply by: Michael H

0

Answer 1

Yes we can get over or under slung axles. It would be very similar to the Dexter Idler Trailer Axle w/ Hubs - EZ-Lube - 5 on 4-1/2 Bolt Pattern - 60" Long - 2,200 lbs part #20545I-EZ-60-10 but you would have them custom make it with the…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 4

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 5

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 6

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 7

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 8

Since Grand Design is kind enough to list certain parts for their trailers I can confirm you have a 33" wheelbase on your 2020 Grand Design Transcend 27BHS. This means the MORryde Rubber Equalizers #MR87ZR will fit your trailer. Although I'm…

view full answer...

Answer 9

Hey Patrick, so for your leaf spring upgrade I am going to need to know a couple of things before I can get you over to the right part. Specifically, the length from eye to eye, the spring width, leaf thickness, and the number of leaves. From here I…

view full answer...

Answer 10

What you're seeing is the Shark fin style camera mount for a Furrion Vision S system like the #FOS05TASF but it looks like the camera was removed. You can install a new Furrion system by plugging the new camera to the existing wire and attaching…

view full answer...

Answer 11

It is possible to replace your 62" long axle with a longer one. Our next size up is going to be a 72" long 2K rated axle like part #e32GR. The axle being 72" across measured from hub-face to hub-face. This axle comes with 5 on…

view full answer...

Answer 12

The Timbren Active Off-Road Bumpstops part #TABSTORSEQ which are a fit for a 2023 Toyota 4Runner are pretty similar to the SumoSprings Solo Custom Helper Springs like part #SS68DR. The Timbrens provide more support but the SumoSprings ride smoother.…

view full answer...