Does Titan Replacement Shock for Model 60 Actuator Come with New Roller Bearings

Question

Question:

Does the roller bearings come with the shock? If not why dont you recommend the roller bearings when replacing the shock? How much are they for Titan 60?

asked by: J C

0

Expert Reply:

The roller bearings part # T0829100 do not come with the replacement shock part # T1242600 for your Model 60 Titan actuator. If yours are still good I wouldn't replace them, but for the price it's hard to pass up.

expert reply by: Jameson C

0

Answer 1

The Replacement Shock for Titan Model 6 and 10 Brake Actuators part #T1242600 only works one way. When the brakes are applied it eases the movement of the trailer forward onto the brake actuator. There is no return spring, the tow vehicle would then…

view full answer...

Answer 2

The shock in a surge coupler actuator like a Titan Model 6 should be extended (to its longest state) when it is at rest (when not under braking load). The shock will be compressed when you apply the brakes by the momentum of the trailer pushing…

view full answer...

Answer 3

To test your shock, you can extend and retract it manually but it will take some force as there should be resistance. It should measure 6 inches from center to center when retracted and 8-1/16 inches when extended. If it is not working properly…

view full answer...

Answer 4

We have not yet replaced the Shock part #T1242600 on a Titan Model 10 Surge Brake Actuator so I do not have any specifics for you but I have attached a parts diagram which shows you how the unit is broken down. You can then use this to get a better…

view full answer...

Answer 5

It's a bit hard to tell based on the picture but it does look like you might have an older Titan Model 6 Brake Actuator like our 8K #T4079200. If this is the case then you can use the Replacement Shock #T1242600 to resolve the issues you're…

view full answer...

Answer 6

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Does Titan Replacement Shock for Model 60 Actuator Come with New Roller Bearings

Product Page this Question was Asked From

Continue Researching