How Do Valve Stems Get Accessed Through Namsco Wheel Covers NA7160B0

Question

Question:

Is there a hole for the valve stem?

asked by: George

0

Expert Reply:

Typically when people use the Wheel Covers part # NA7160B0 they also install valve stem extenders like part # WM8029 which allows them to be accessible through the cover. This allows the valve stem to be reached through the smaller holes that line the outside of the cover.

expert reply by: Jameson C

0

Answer 1

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is…

view full answer...

Answer 2

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack…

view full answer...

Answer 3

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need…

view full answer...

Answer 4

Replacement arms are available for the Roadmaster EZ5 Base Plate Kit #RM-521569-5 for your 2015 Honda Fit with the part #RM-ARMS. When the original base plate brackets and arms were manufactured, they were made as one part. To be sure that the new…

view full answer...

Answer 5

The overall size of the Furrion Over the Range RV Convection Microwave part#FMCM15SS is 29-15/16" wide x 16-3/8" tall x 15" deep and requires a 30" cutout. If this matches the opening and size of the model you have this will be a…

view full answer...

Answer 6

Your 265/70R17 size tire is around 31-1/2 inches in diameter. You want to make sure the tire cover you get is large enough and doesn't have to be stretched over the tire. I'd rather have one that's slightly loose than one that tears…

view full answer...

Answer 7

Yep, you're exactly right; the distance from the center of the hitch pin hole to the welded gusset is indeed four inches on the Curt Ball Mount for 2" Hitches #C45112. So if that's the amount you need for it to work without hitting the…

view full answer...

Answer 8

The biggest difference between the Tow Ready Tail Light Isolating Diode System #TR118821 and the Roadmaster Universal Hy-Power Diode Wiring Kit #RM-154 is that Tow Ready created their wiring kit with quick disconnects so if you ever get a new vehicle…

view full answer...

Answer 9

You will want to cut the yellow and green wires and connect the ends with a yellow butt connector. Then attach a small length of wire to both butt connectors and attach the wires to the input of the diode with spade connectors and then attach the…

view full answer...

Answer 10

If your step motor marked "REP 851" and the Part Number sticker says "32 Series Step," the replacement step motor kit you need is the Kwikee #LC379145 Motor Upgrade Kit. You can further confirm that you have a Series 32 step kit…

view full answer...

Answer 11

There is a solution for you, but the lift kits you referred to such as #K71-725-02 will not work with welded on torsion axles. The best option is for you to simply remove your torsion axles and use the Timbren Axle-Less Trailer Suspension System…

view full answer...

Answer 12

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

How Do Valve Stems Get Accessed Through Namsco Wheel Covers NA7160B0

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching