How to Grease the Gears on the Pro Series Round, A-Frame Jack, # PSEA20000103

Question

Question:

how do you grease this jack when needed?? I see no grease fitting.

asked by: Bonny

0

Expert Reply:

To grease the gears on the Pro Series Round, A-Frame Jack, # PSEA20000103, you would need to remove the handle and top plate to expose the gears. The gears come already greased but if more is needed, you would have to completely remove the old grease (not all greases are compatible with each other) before adding the new grease like LubriMatic LMX Industrial Strength Grease, # L11390.

expert reply by: Michael H

0

Answer 1

Yes, the Pro Series 12,000 lb Square Jack, #PS1400950376, does have a grease fitting built into the front of the jack. You can see the grease fittings in the photos on our product page. It will be located between the handle and the warning sticker. I…

view full answer...

Answer 2

The Bulldog Replacement Sidewind Gear Kit #BD500212 that you referenced is the correct repair kit for your Bulldog square tube jack according to my contact at Bulldog. The top cap you can use is part #BD017802. After you repair the jack you will want…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 6

Good news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears #TJD-12000-RODNUT in the #12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience. Basically,…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Waylon, it does look like the Dexstar Steel Mini Mod Trailer Wheel #AM20539 is the same thing as the Dexstar 17-233 wheels you're referring too. These are silver wheels with a 6 on 5 1/2 bolt pattern, a 0 offset, and are made in the USA.

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

To repair a Ram Series 12000 jack, like #TJD-12000SP-R2, we have the Gear Kit #TJD-12000-GR or the Replacement Rod and Nut #TJD-12000-RODNUT. Or you could need both. I just depends on what the problem is exactly.

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...