Does etrailer Axle Teknology 10-Inch Brake Assembly AKEBRK-35L Include Trailer Wiring

Question

Question:

Does electric brake AKEBRK-35L come with a trailer wiring run? Some reviews said yes and others said no.

asked by: Doug W

0

Expert Reply:

The etrailer Axle Teknology 10-inch brake assembly # AKEBRK-35L and the matching right-hand unit # AKEBRK-35R come with two wire leads (from the brake magnet) that are just a few inches long. The actual 10-gauge wire you'll use to install the brakes, # 10-1-1, is offered by the foot.

Either wire lead from each brake can be used for hot or ground since these are non-polarized.

Often parts like junction box # 38656, 7-pole plug # H20046 and ring terminals # DW05741-1 are used to complete an electric brake installation.

expert reply by: Adam R

0

Answer 1

The UFP HD377 is a 10 inch hub drum for a typical 3.5K axle. The #AKUBRK-35-D brake assembly you'd looked at is compatible with a 10 x 2-1/4 inch hub drum, as long a the inside width and depth dimensions of your existing hub match that, the…

view full answer...

Answer 2

We do have what you need to replace the UFP HD-1377-10 hub and drum as well as add hydraulic brakes for your boat trailer. Here are the exact parts you will need: - Dexter Trailer Hub and Drum Assembly #84546UC3 - Hydraulic Trailer Brake Kit -…

view full answer...

Answer 3

The Replacement Shock Absorber Spring Kit #TK71-758-00 is the correct shock for your UFP Surge Brake Actuator. The picture you included does not specify if it is for a disc or drum brake set, so I have found both for you to choose from. Disc Brake…

view full answer...

Answer 4

If you replace the current brakes on your trailer with the same uni-servo drum brakes and no lockout actuator (like #T2351000), the brakes will deliver 20 percent braking when traveling in reverse. However, the more pressure you apply going backwards…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...