Plastic Fender Recommendation for Shorelander Trailer with 14 inch Wheels

Question

Question:

I have a 1993 Shorelander single axle trailer with 14foot tires that needs a new plastic white fender. The mounting brackets are 31.25inch apart. what do you reccomend?

asked by: Ron R

0

Expert Reply:

It looks like the closest fender we have that should work well would be the part # F008574. If you check out the dimension picture that I attached you will see that the mounting bracket dimensions for this fender should match up well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

For the 13" #CE19503-2 there is a distance between the two outside mounting on center of 33-3/4 inches and 29-3/4 inches between the two inside holes. The holes on the mounting surfaces are spaced apart 5 inches vertically and 2 inches…

view full answer...

Answer 2

We have a very close option with the #CE19503-2 which is off by only 1/4 of an inch to the measurements you listed. It measures 29-3/4 inch for the inside portion and 33-3/4 inch for the outside portion.

view full answer...

Answer 3

I went out to our warehouse to take a look at both the CE Smith Single Axle Trailer Fenders - 12" Grey #CE19502-2 and the larger 13" Black #CE19503-2. Both options represent the only color available from CE Smith in the respective…

view full answer...

Answer 4

Thank you for the photos! According to my information and what you sent in, your best option for a replacement fender is the CE Smith Black Fender: CE Smith Single Axle Trailer Fender w/ Top and Side Steps - #CE19503 (Qty 1) CE Smith Single Axle…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Answer 12

Hey Kevin, for your Demco DA70 actuator you can use the Reverse Lockout Solenoid for Demco Hydraulic Brake Actuators #DM11993.

view full answer...

Plastic Fender Recommendation for Shorelander Trailer with 14 inch Wheels

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching