Tripod Stabilizer for a 5th Wheel Trailer with Gooseneck Adapter On It

Question

Question:

I have a king pin stabilizer but I have the goose neck adapter on my camper can I buy a adappter to change the king pin on stabilizer and change it to the goose neck stabilizer? It just unscrews out of the top of the stabilizer

asked by: Jerry M

0

Expert Reply:

We actually have a tripod stabilizer designed for gooseneck trailers that you can use. It is # UF19-950450. It is height adjustable from 31 to 54 inches. It is rated for 5,000 pounds.

And adapter for a 5th wheel stabilizer tripod # UF19-001056, is also available.

expert reply by: Michael H

0

Answer 1

The shorter arms included in the Lippert Components JT's Strong Arm Jack Stabilizer #LC191024 measure 21-3/4 inches retracted and just about 43 inches when extended. This measurement is from the center of one hole to the center of the other. This…

view full answer...

Answer 2

Installing ta Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Adapter Pin Box like the #325-GH-8045 would not void the warranty of your camper, and Gen-Y makes some of the most durable parts on the market. I really like this as an alternative to…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 7

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 8

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 9

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 10

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 11

The factory prep package or pucks are not the same between Ram, GM and Ford. The spacing is all different which means you cannot use a 5th wheel hitch for Ram pucks on a GM with pucks. Take the Curt A25 5th Wheel Trailer Hitch for example which is…

view full answer...

Answer 12

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...