Can Draw Tite/Reese Signature Series Fifth Wheel Hitches Fit Ford Hitch Prep Rail Kits

Question

Question:

are there adapter pucks and/or s to make the older signature series fit the new Ford OEM underbed

asked by: Bj

0

Expert Reply:

Yes, for an adapter to allow an older Signature Series Reese hitch to fit the Ford Hitch Prep package you would need the # RP58419.

expert reply by: Jameson C

0

Answer 1

The outer diameter of the inner recessed section on the Replacement Trim Rings for Reese Elite Series 5th Wheel Rail Kit part #RP58458 is 2-5/8".

view full answer...

Answer 2

I contacted our representative at Draw-Tite about replacement trim rings for your Reese 18K Elite Series on your 2008 Chevrolet 2500. For a full set of 4 trim rings, you will need Replacement Trim Rings, part #RP58458. For just one ring and…

view full answer...

Answer 3

We do have replacement parts for the Reese Fifth Wheel Installation Kit, #RP30073. The replacement puck is the Draw-Tite Replacement Signature Series Puck Service Kit, #58253, and it is the puck, trim ring, bolt and lock washer. The puck plug cover…

view full answer...

Answer 4

If all you need is covers for the Ford hitch prep package pucks that you have on your truck all you would need is the part #58199. If you need the trim rings you would want the part #RP58458 which comes with 4 rings. Unless you need the service kit…

view full answer...

Answer 5

Yes, the B&W Turnoverball Underbed Gooseneck Trailer Hitch #BWGNRK1111 fits a 2012 and a 2015 Ford F-250 whether they have a long or a short bed. Please note that if you have already installed this gooseneck hitch once you will need to use new…

view full answer...

Answer 6

The factory prep package or pucks are not the same between Ram, GM and Ford. The spacing is all different which means you cannot use a 5th wheel hitch for Ram pucks on a GM with pucks. Take the Curt A25 5th Wheel Trailer Hitch for example which is…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 11

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 12

Yes you are - all 5th wheel hitches are going to require some type of rails in order to be used. So you'd need #DM8552016-71 for your 2006 Dodge Ram.

view full answer...

Can Draw Tite/Reese Signature Series Fifth Wheel Hitches Fit Ford Hitch Prep Rail Kits

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching