Diameter for Puck Cutout Using the Replacement Trim Rings for Reese Elite Series 5th Wheel Rail Kit

Question

Question:

What size is the bottom inner circle on these trim rings? I want to buy the correct hole saw to cut the holes in my truck bed and have theses trim rings fit in snugly.

asked by: Dan F

0

Expert Reply:

The outer diameter of the inner recessed section on the Replacement Trim Rings for Reese Elite Series 5th Wheel Rail Kit part # RP58458 is 2-5/8".

expert reply by: Conner L

0

Diameter for Puck Cutout Using the Replacement Trim Rings for Reese Elite Series 5th Wheel Rail Kit
(click to enlarge)

Answer 1

Yes, for an adapter to allow an older Signature Series Reese hitch to fit the Ford Hitch Prep package you would need the #RP58419.

view full answer...

Answer 2

I contacted our representative at Draw-Tite about replacement trim rings for your Reese 18K Elite Series on your 2008 Chevrolet 2500. For a full set of 4 trim rings, you will need Replacement Trim Rings, part #RP58458. For just one ring and…

view full answer...

Answer 3

We do have replacement parts for the Reese Fifth Wheel Installation Kit, #RP30073. The replacement puck is the Draw-Tite Replacement Signature Series Puck Service Kit, #58253, and it is the puck, trim ring, bolt and lock washer. The puck plug cover…

view full answer...

Answer 4

If all you need is covers for the Ford hitch prep package pucks that you have on your truck all you would need is the part #58199. If you need the trim rings you would want the part #RP58458 which comes with 4 rings. Unless you need the service kit…

view full answer...

Answer 5

I did contact B&W on your behalf. If by side panel you are referring to the side panels of the upright arms that hold the head of the hitch in place, we do sell the Replacement Base #BWRVB3200 for the B&W Patriot 5th Wheel Trailer Hitch…

view full answer...

Answer 6

The B&W Companion Gooseneck-to-5th-Wheel Trailer Hitch Adapter - Dual Jaw - 20,000 lbs #BWRVK3500 has the polyurethane molded bushings on the pivot arms. This is where noise and squeaking could come into play, so the manufacturer recommends using…

view full answer...

Answer 7

The B&W Companion 5th Wheel Trailer Hitch #BWRVK3500 (RVK3500) is the complete 5th wheel hitch that will mount to an existing B&W Turnoverball Gooseneck Hitch socket in the truck bed. The part #BWRVB3500 (RVB3500) that you also referenced is…

view full answer...

Answer 8

Since you purchased a Reese 18K hitch for Ford Factory pucks the foot #58238 is what you need for the older style Signature series fifth wheel hitches and is a replacement foot assembly kit. If you have the newer style, then #RP58419 is what you need…

view full answer...

Answer 9

Yes and no... The puck design that the #58238 fits is the same as the Ram rail kits, BUT there isn't a hitch that this adapter fits that has the correct puck spacings to fit a Ram rail kit. The Ram rail kits are spaced differently than the Ford…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...