How to Determine the Wheel Bolt Pattern on My Trailer Wheel is it 5 on 4-1/2 or 5 on 4-5/8

Question

Question:

It is really hard to tell on a 13 inch wheel with 5 lugs if it is 4 1/2 or 4 5/8 Will it work if I order a 4 1/2

asked by: gary m

0

Expert Reply:

Your wheel should be a 5 on 4-1/2. A 5 on 4-1/2 or 5 on 4-3/4 is what is offered for a 13 inch wheel, I have never actually heard of a 5 on 4-5/8 wheel.

The Dexstar Steel Spoke Trailer Wheel you were looking at, part # AM20232 should work fine for you.

expert reply by: Mike L

0

Answer 1

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 2

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 3

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 4

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 5

In order to install a brake controller on a dump truck you'd first need to start with a 4-way trailer connector and then adapt this to a 7-way so you can hook up a brake controller. I won't have much info for anyone particular dump truck but…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 9

We do have a compatible grease seal for your 168255TC oil seal, however, we do not carry rubber coated seals in this size. The 168255TC oil seal was designed to work with oil bath hubs on a 3,500 lb axle. For the most part, axle manufacturers have…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 12

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

How to Determine the Wheel Bolt Pattern on My Trailer Wheel is it 5 on 4-1/2 or 5 on 4-5/8

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching