Height of Replacement Pintle Sleeve for Convert-A-Ball Pintle Hook Combos

Question

Question:

Id like to add the convert-a-ball system to a BandW tow and stow pintle set up. Can you let me know the height of the sleeve?

asked by: Matt

1

Helpful Expert Reply:

The Replacement Pintle Sleeve for Convert-A-Ball Pintle Hook Combos # PS measures 3-3/16 inches tall. I have attached a diagram showing this measurement for you.

expert reply by: Victoria B

1

click to enlarge

Answer 1

The hardware that comes with the Curt hitch part #C11030 that you referenced is Grade 5 which means it is zinc coated to fight corrosion. Zinc coating isn't quite as corrosion resistant as stainless steel but it does a good job preventing rust.…

view full answer...

Answer 2

You would want to mount the Convert-A-Ball Pintle Hook Combo #PH1 to a mount such as #AMPC3 both of which use 1/2 inch bolts.

view full answer...

Answer 3

Most pintle hooks use a standard bolt pattern which is 3-3/8" horizontally center to center and 1-3/4" vertically center to center (see photo). Therefore, the Pintle Hook part #C48231 would be a direct fit and work well for you. It also…

view full answer...

Answer 4

The replacement pintle sleeve #PS has an outer diameter just under 1-7/8 inches.

view full answer...

Answer 5

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 6

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 7

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 8

You can get a new brake mounting flange for your axle. The old flange will need to be cut off. The part is #4-44-1. This is designed to fit a 3 inch trailer axle and should be welded in place by a professional. Since you would also have to get the…

view full answer...

Answer 9

We do have 205/75R14 size radial tires that have a load range of D and a speed rating of at least 81 mph. Out of our available selection I recommend going with the Kenda Karrier #AM10235. This tire has a max load rating of 2,200 lbs at 75 psi and a…

view full answer...

Answer 10

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 11

In regards to the Correct Track Trailer Alignment and Lift Kit part #RR23QX, the kit provides a lift by essentially extending the hangers. This normally requires cutting off the old hangers and welding on new, taller ones but with this kit you…

view full answer...

Answer 12

The Correct Track Trailer Alignment and Lift Kit - Tandem Axle #RR23QX does come with all of the components needed to lift a tandem axle trailer. The center hangers of a tandem axle setup use different components than the front and rear hangers since…

view full answer...

Height of Replacement Pintle Sleeve for Convert-A-Ball Pintle Hook Combos

Product Page this Question was Asked From

Continue Researching