What Size Bolts are Used to Mount Convert-A-Ball Pintle Hook Combo # PH1

Question

Question:

What size holes in the plate for bolts?

asked by: Garry

0

Expert Reply:

You would want to mount the Convert-A-Ball Pintle Hook Combo # PH1 to a mount such as # AMPC3 both of which use 1/2 inch bolts.

expert reply by: Michael H

0

Answer 1

The Buyers Products 15 Ton Pintle Hook part #337PH15 does have the 30,000 lb. GTW and the 6,000 lb VLL ratings you are requiring. If you want the same capacities but with a 2 6/16" ball then the Convert-A-Ball Pintle Hook Combo with 3 Stainless…

view full answer...

Answer 2

There isn't a pintle adapter for ball mount #C45902 rated for 21,000 pounds but I may have a solution for you. What you could do is use ball mount plate #337PM25812 with Convert-A-Ball pintle hook combo #PH1. When used as a pintle hitch the…

view full answer...

Answer 3

The Curt Adjustable 2-Ball Mount #C45902 is manufactured overseas. If you are looking for a similar made in the USA adjustable ball mount the Flash Solid Steel HD Adjustable 2-Ball Mount #FA49-00-5625 has the same 2-1/2" receiver, 6" drop,…

view full answer...

Answer 4

It sounds like you are referring to the sleeve in which case you can use the Replacement Pintle Sleeve for Convert-A-Ball Pintle Hook Combos part #PS which works with the Convert-A-Ball Pintle Hook Combos part #PH1 and part #PH2. If this is not what…

view full answer...

Answer 5

The Convert a Ball pintle adapter #PS fits the #PH1, #PH2, PH2S, and the #PH4 but not the PH3. That might be an easier way for you to determine if this will fit what you have without measuring. I am not sure what you mean by 6 way.

view full answer...

Answer 6

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 7

The reason why changing from a 4-leaf double-eye springs, like part #e47SR, to a 5-leaf double-eye spring of the same capacity, like part #e34SR, won't matter in a situation like what you have is because it's all about the strength of the…

view full answer...

Answer 8

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 9

I can give you some guidance on how to determine the correct replacement leaf springs, and you are right that replacing all four of them at the same time is a good idea. What you'll need to do for double-eye springs (which is what I assume is on…

view full answer...

Answer 10

You shouldn't loose any wheel clearance with the Dexter E-Z Flex Suspension Kit. First you will want to see which of the Equalizers you need. There is a 6,000lb Equalizers #K71-654-00 (5-5/8") and 8,000lb Equalizers #K71-655-00…

view full answer...

Answer 11

Yes the 4,000-lb leaf spring is compatible with a 3,500-lb axle. There are a couple of important measurements. Spacing from eye to eye on the spring when unloaded with no weight on the axle. Inner eye diameter of the spring roll Spring width from…

view full answer...

Answer 12

The Replacement Pintle Sleeve for Convert-A-Ball Pintle Hook Combos #PS measures 3-3/16 inches tall. I have attached a diagram showing this measurement for you.

view full answer...