What Does the SH Error Code and a Single Dot Mean on the Prodigy Break Controller, # 90885
Question:
Today after stopping for gas my Prodigy Break break control was flashing NC and SH. I assume NC is no connection but unsure what the SH is indicating. Never saw either of theses codes before. I unplugged and reconnected the controller connection and plug in at rear of truck with no change. Drove out on highway and C came back on and breaks seemed to work properly when stopping. I also noted that there is only one red dot vs two on screen when trailer is unhooked. What does SH indicate and what do I need to check to trouble shoot the problem? Is this a problem with the controller or wiring? What does the single red dot vs two indicate? I drive a 2002 Ford F150
asked by: Larry G
Expert Reply:
The SH code on the Prodigy Brake Controller, # 90885, indicates that while idle, the brake controller is sensing a short in the brake wire. Tekonsha states that some test lights or non-Tekonsha testers can cause this problem. The NC code means no trailer is connected. The cause to both of these error messages may be solved by cleaning both the vehicle side and trailer side connectors of any dirt or corrosion. Also make sure the brake wire from the controller to the 7-Way is not broken or pinched anywhere. I also recommend checking the ground from the trailer connector to the trailer is secure and free of dirt and corrosion.
The single dot indicates that the boost feature is not on. Two dots means that the boost feature is on.
You might want to also check the actual trailer brake magnets. If a magnet is not grounded properly or is very worn it could cause fault errors in the system. I have included a link to the installation details for the Tekonsha P2, # 90885, below.
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Troubleshooting Error Codes SH and OL on a Tekonsha Prodigy Brake Controller
- Shop: Brake Controller
- Shop: Trailer Hitch
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles
- Shop: Trailer Wiring
- Shop: Camco Cam Lock - Straight or Offset - Key Operated - 5/8" Thick
- Shop: RV Interior Lighting
- Video: Camco RV Locks - Baggage Door Lock - CAM44340 Review
- Shop: Safety Step Adjustable Height, Folding Platform Step - Aluminum - 24" x 16" - 1,000 lbs
- Q&A: How To Choose Correct Swing Out Extension Brackets for Truck Camper Jack Systems
- Shop: MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 2-1/4" Long Shackle Straps
- Shop: MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 3-1/8" Long Shackle Straps
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: EZ Connector Custom Vehicle Wiring Harness w/ Magnetic 7-Way Trailer Connector
- Q&A: Replacement Pin for an LBS48-16 ESCO Break Away Switch
- Search Results: trailer hitch
- Q&A: Testing for Proper Voltage on the Brake Output Circuit
- Q&A: Testing a Vehicle Side 7-Way Trailer Connector for Proper Function
- Article: Troubleshooting Brake Controller Installations
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: How to Wire Electric Brakes on a Tandem Axle Trailer
- Q&A: Does the Tekonsha P3 Trailer Brake Controller Turn Off or Stay On All the Time
- Search Results: 7pin
- Search Results: 7 pin connector bracket
- Video: EZ Connector Wiring - Trailer Connectors - 319-R7-01 Review
- Video: Tuson Electronic Sway Control System Review
- Search Results: ez connector
- Video: Review of Pollak Wiring - Trailer Connectors - PK12-707E
- Search Results: tekonsha
- Search Results: tekonsha p3