Testing for Proper Voltage on the Brake Output Circuit
Question:
What should voltage output from plug on vehicle be going to trailer brakes. Mine is .2 V.
asked by: Shorty R
Expert Reply:
There are many things that can affect the voltage on the brake output wire from your brake controller to your trailer brakes such as the power setting on your brake controller, how you are testing the wire and if you are testing it with the brakes or manual override activated.
Using a multimeter to test the voltage on the brake output wire at your trailer connector will not always give the proper reading because it does not provide a load on the circuit like brake magnets from a trailer would. Instead of using a multimeter, I recommend using a circuit tester like part # PTW2979. This circuit tester has an incandescent bulb that will apply a load to the circuit that will allow full power to be applied on the wiring.
To test for proper voltage on the brake output wire, set the power gain on your brake controller to the maximum. Have someone apply the manual override on the brake controller while you use a circuit tester to test the pin on the trailer connector for the trailer brakes. If the light is bright, then you know you are getting full voltage.
If you are experiencing poor braking with full voltage, then the issue is likely on the trailer. Make sure your trailer brakes are adjusted properly and you could also check your brake magnets. I have attached an FAQ article on testing your brake magnets for you to check out if you feel that this is a possible issue.
If the 0.2 volts that you are getting is when the brakes are not being applied then that is the signal that the brake controller sends back to the brake magnets to detect if a trailer is connected or not.
If the light is dim when the manual override is applied, then we will need to do further troubleshooting. I would first check that all of the wires from the brake controller (ground, 12 volt power, stop light switch) are properly connected. If all of the connections look secure, then you can cut the blue wire about 6 inches back from the brake controller to test for voltage there. If you have full voltage at that point, we know there is an issue on the brake output circuit somewhere between that point and the trailer connector. Check the vehicle side trailer connector for corrosion or a poor ground connection and you should also check the brake output wire for any damaged sections that could cause a drop in voltage.
If you do not have the proper voltage at that point, the brake controller is likely bad and will need to be replaced. If you determine that a replacement is necessary, I would recommend the Tekonsha Prodigy P2, # 90885. This is a proportional brake controller that will provide a smooth ride by applying the trailer brakes with the same intensity as the tow vehicle.
If you are unable to find the problem or a solution after following these steps, let me know what you come up with and we can do further troubleshooting.
Products Referenced in This Question
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Product Page this Question was Asked From
Pollak Heavy-Duty, 7-Pole, Round Pin, Trailer Wiring Connector - Trailer End
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- Plug Only
- 7 Round - Round
- Pollak
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Testing Trailer Brake Magnets for Proper Function
- Shop: Brake Controller
- Shop: Cordless Circuit Tester
- Shop: Trailer Wiring
- Shop: Towing Mirrors
- Video: Review of Dexter Trailer Hubs and Drums - Hub with Integrated Drum - 8-407-5UC3-EZ
- Video: Trailer Brake Controller Wire Testing
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Hook Probe Circuit Tester
- Shop: Grease Seals 10-36 (pair)
- Article: Trailer Wiring Diagrams
- Shop: etrailer Electric Trailer Brakes - 7" - Left/Right Hand Assemblies - 2,000 lbs
- Shop: Bearing Kit, LM67048/25580 Bearings, 10-36 Seal
- Shop: Dexter Electric Brake Assembly for 4.4K Axles Manufactured After May 2009 - 10" - Left Hand
- Q&A: Voltage at Brake Magnets is 8 Volts with Brake Controller Set to Maximum
- Search Results: trailer brake controller
- Q&A: What Ohms Should Trailer Brake Magnets Be?
- Shop: Suspension Enhancement
- Q&A: Electric Trailer Brakes not Working
- Search Results: trailer brakes
- Search Results: hopkins 7 pin connector
- Search Results: grommet
- Search Results: 37185
- Shop: Gooseneck Hitch
- Search Results: 7 way trailer wiring
- Q&A: Why Would Brand New Trailer Brakes Feel Weak
- Shop: RV Interior Lighting
- Q&A: How Long Does It Take to Install B&W Turnoverball Underbed Gooseneck Trailer Hitch BWGNRK1020
- Search Results: gooseneck hitch
on Trailer Wiring
