Replacement Lens Availability for a Tracker Pontoon Boat Trailer Clearance Light

Question

Question:

Hi, Will the108-15A fit my side marker light? The only # on lens is SAE AP-2-88-DOT. The dimensions on mine are 4x2x3/4inch at the highest point, tapering down to 1/2inch on the ends. It is a tracker pontoon boat trailer. Thanks

asked by: Jack B

0

Expert Reply:

The light the part # 108-15A is designed to fit is the # 423000 which I attached a dimensional drawing of. You would need to compare that to what you have to know for certain.

Or another option to check out is the part # 34-59-012 as it sounds more like what you have.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The SAE codes on the lens of a light indicate what function(s) that light can perform. Many trailer lights are designed to do more than one function. Based on the SAE codes on the first light, it performs the following functions: A - Rear reflector…

view full answer...

Answer 2

We have exactly what you need. For the amber lens light you would want the Oval Clearance Light part #MC38AB and then for the red light you would want the Peterson Red Oblong Clearance Light part #423000.

view full answer...

Answer 3

I'm assuming that you're speaking of the Optronics #MCL31RB side marker/clearance lamps. These lamps are designed to surface mount using machine or self tapping screws as shown in the photo I've provided for you. A gasket isn't…

view full answer...

Answer 4

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

It is not uncommon for certain factory brake controllers to have issues with electric over hydraulic brakes. This would be the first we have heard of this issue with a 2023 Ford F-350, but it is possible that the brake controller in your ford is…

view full answer...

Answer 12

To get power to the controller of your Solera Smart Arm 12V Power RV Awning part #LC759404, you need to tap into an existing circuit, or run a power wire from the battery with an inline fuse holder, and a 15 amp fuse, like part #SWC9538, and part…

view full answer...