Hitch Recommendation for a 1993 Dodge Roadtrek Camper Van

Question

Question:

will this bolt on to a 1993 dodge roadtrek camper van with the storage compartment in the rear area. 190 popular Thanks,

asked by: Ron P

0

Expert Reply:

I spoke to my contacts at Curt and Reese and the only styles of hitches that can be made to fit a camper van like yours are multi-fit hitches like the # 41990 that has a 16k capacity. This is a weld on hitch that would require either the 7 inch drop brackets part # 4907 or the 16 inch brackets part # 4916.

expert reply by: Jameson C

0

Answer 1

The best option we have available for your 2008 Sterling Bullet Cab and Chassis is the Draw-Tite Ultra Frame Service Body Trailer Hitch #41991 paired with the 16" Weld-On Bracket Kit #4916. These extra long brackets will give you the drop needed…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 5

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

Yes, our Dexter leaf spring part #DX74XR is the same as the part number 072-079-00. This is a 7-leaf spring for an 8,000 lb trailer axle that is 24-7/8 inches.

view full answer...

Answer 10

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

The weight is 54 lbs for the Superwinch S7500 Trailer Winch #SW1475201.

view full answer...

Hitch Recommendation for a 1993 Dodge Roadtrek Camper Van

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching