Replacement Follower Leg Recommendation for Landing Gear Set VMC900L

Question

Question:

Have a 2003 Keystone Sprinter26foot L/A model. have a bad follow leg model #VMC900L-015071. Which one is the best replacement? should I replace both landing gears at this time? Any help would be great.

asked by: Richard

0

Expert Reply:

The correct replacement follower leg for your set that has model number VMC900L is the part # LG-177201.

If your other leg is still working fine there would be no reason to replace it at this time.

expert reply by: Jameson C

0

Answer 1

For your Venture landing gear set the correct follower leg you'd need is the part #LG-179014 which matches what you sent in a picture of.

view full answer...

Answer 2

Sounds like the correct follower leg you would need is the #LG-179014 that you referenced. The overall length of the leg is 33-1/2 inches and the distance from the inside of the two brackets is 17-1/2 inches. Check out the picture I attached for more…

view full answer...

Answer 3

The only follow leg I can recommend you use with your Venture landing gear would be the part #LC179014. Stromberg Carlson makes the Venture landing gear, that is the brands are different but the jacks are the same. I cannot recommend you install a…

view full answer...

Answer 4

The internal parts (screw and nut) on your Venture landing gear are not available as replacement parts but we may have a replacement leg. We carry several legs that could potentially work. Lead: #LC119102 (outer tube is 29-1/2 inches overall) Follow:…

view full answer...

Answer 5

Since your Venture leg is the follow leg the repair kit is #LC146060. If you had the lead leg it would be #LC146059.

view full answer...

Answer 6

The industry standard for sewer pipes for RVs is 3 inch. What you have on your 2008 Carriage Cameo would be 3 inch like what the part #LC359724 is designed to fit.

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Replacement Follower Leg Recommendation for Landing Gear Set VMC900L

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching