Roller Bunk Recommendation for a 10 foot Section of Bunks

Question

Question:

Are the deluxe roller bunks available in 10 ft lengths or will I have to order 2 sets of 5 footers to match my existing bunks.

asked by: Wayne A

1

Helpful Expert Reply:

The longest section of roller bunks we offer is 5 feet like the part # DL21741 that you referenced.

For a 10 foot long section you would want to use one 5 foot section like the # DL21741 and then a set of 4 feet long roller bunks like the part # DL21740. The reason for this is that each roller bunk has a roller at the end of it. Since the rollers are spaced 1 foot apart on the bunks you would want 1 foot between each set to equal 10 feet and have the rollers spaced evenly.

expert reply by: Jameson C

1

Answer 1

Dutton-Lainson doesn't manufacture a 9 foot long roller bunk, however you could use two 5 foot roller bunks per each side part #DL21755, for a total of four. The small bit of extra length won't hurt anything. Each 5 foot section has a…

view full answer...

Answer 2

Smart idea to get ahead of the problem, and there is a good upgrade for your Tracker boat trailer with a 3,500 lb axle. Since your current spring measures 26-1/4 inches from center of one spring eye to the center of your other spring eye, a 26 inch…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 6

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 7

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 8

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

Your trailer looks awesome! The Road armor equalizers #LC696740 and Equa-Flex Cushioned Equalizers #LC279687 are both pretty similar in performance even though the Road Armor has two dampers. The main difference is the size of the equalizers. The…

view full answer...

Roller Bunk Recommendation for a 10 foot Section of Bunks

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching